Zanussi Washing Machines - Page 2 - Recent Questions, Troubleshooting & Support
Zanussi washer zwh8 100se. Message EH0 and E40?
Zanussi Washing Machine Error Code = E40
?Error Code Definition = The washer door is either open or not properly closed.?
What To Check or Repair = Check that the door is completely closed. Check that nothing is blocking the door from closing.
Zanussi Washing Machine Error Code = EH0?
Error Code Definition = The electrical supply is not stable. Wait until the mains supply is stable.?
What To Check or Repair = Check electrical circuit breaker. Unplug the washer for 10 minutes to reset.
Zanussi washing machine door wont lock
No, the door interlock is an important safety feature, after a young boy had his arm removed by a spinning washing machine. You have to fix it, not bypass it. My guess is that is is badly adjusted and the lock is not fully closing to trigger the microswitch. You can just join the wires together, but that might cause further problems. All these machines are electronic and the have 'what is happening? What do I do now?' logic. you can try it, but not if you have kids please.
There are videos here. Watch them and see if you did it right and if they have information on adjustment?
https://www.google.com/search?q=zanussi+washing+machine+door+lock+replacement
..
Machine won't restart after reset, 'start/pause' button flashing.
Hello,
When you put it to drain/spin does the pump make any attempt to drain,if not it could be that there is something stuck in the pump,needs draining manually.Another thing to try is to find the fault code.If you hold down the 2 buttons on the far right of panel then press on/off button till lights start chasing,then release the 2 buttons on right hand side.Now the first function button by the on/off button you will need to press until the light above the button reaches the 9th or 10th position this will give you a read out in the display.
E10 = low water press.
E20 = pump or filter.
E30 = press. switch or heater faults.
E40 = Door swich.
E50 = motor.
Some of these numbers can vary there are more but those are the most common.After checking codes switch off machine then back on twice to reset.
Hope this helps.
E34 error zanussi washer
Incongruence between level of electronic
pressure switch and level of anti-boiling
pressure switch 2 (duration of fault at least 60
seconds).
Cycle is blocked with door closed.
Could be: Hydraulic circuit of pressure switches; electronic
pressure switch; pressure switch; wiring between main PCB and electronic pressure switch; wiring between main PCB and safety pressure switch; and finally main PCB.
Dado
Zanussi Lindo100 child lock flashing
To turn the child lock off on this all you need to do is press and hold the temperture button and the spin button together for about 5 seconds and it will turn the child lock off from there.
How could I reset a Zanussi zwf580 WM that no matter which program I select, it changes automatically to the drain mode light?
If the START / PAUSE button lights up red, the washing machine detects a malfunction. Now you should count how many times the START / PAUSE button lights up red and tell to us what kind of malfunction is being done.
Try to rapid reading of alarm codes when the appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and the nearest option button for at least two seconds: the LEDs initially switch off, and then display the flashing sequence indicating the last alarm.
LED indicator START / PAUSE with red light = indicates the first digit of the alarm code (family)
• LED indicator START / PAUSE with green light = indicates the second digit of the alarm code (internal number of the family)
Dado
Zanussi washing machine ZWF71443W door will not open after wash
Is this the first time it's happened? Normally, a washing machine door won't open if a) not enough time has passed since the end of the cycle to the door unlocking itself, in which case you'd wait till for the unlocking click. You could also just switch the machine off, then switch off the power to it, then wait for 30 seconds before switching on again. OR b) the level of water inside the drum is too high. Have you checked that it has drained properly? Or if there is any blockage in the filter (usually behind a square panel bottom front of the machine), which may need cleaning out. Or a blockage in the drainage hose (at the back and connected to your water to drain pipe). Also, on some models, where you'd access the filter (and clear the fluff out from), there is often an emergency door opening lever beside it which you have to put down. But this should be a last resort. If you do have to use it, you have to reset the machine after by switching off power, waiting for 30 seconds then switch power back on again. Hope this helps and one of them works.
Not finding what you are looking for?