Question about Konica Minolta bizhub Office Equipment & Supplies

1 Answer

When I replace the image transfer belt unit on a bizhub 203 does it have to be reset?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Konica Minolta Master
  • 1,316 Answers

No,the transfer belt unit resetting automatically.

Posted on Mar 31, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 214 Answers

SOURCE: transfer unit on bizhub C250

its not so hard, open side door, remove 2 screws, and pull out the transfer unit gently. and reinstall new TBU. BE VERY CAREFUL WITH NEW UNIT, DO NOT DAMAGE IT.

Posted on Jun 19, 2008

  • 12 Answers

SOURCE: Reseting counter after installing new image transfer roller unit

You need to go into tech rep mode to reset.
press: stop 0 0 stop 0 1, then 0 0 0 0 0 0 0 0, press enter, then press counter on the left, select life, then highlight image trans roller and press the C button, repeat for paper dust remover and exit tech rep mode

Posted on Apr 06, 2009

  • 12 Answers

SOURCE: Imaging Unit Problem with bizhub C450

On the end of the image unit you will find a white bit of plastic with a small screw in the middle, make sure this screw is tight and then reinstall the units(give the units a bit of a shake too)

Posted on Apr 06, 2009

Bizhubman
  • 108 Answers

SOURCE: how to reset the transfer unit (fuse?), do you

76e2129.jpg
Hope this helps. Make sure you remove the waste tank prior to taking out the transfer belt. Belt is removed by two screws inside right door and sliding the unit out.

Posted on May 17, 2010

  • 118 Answers

SOURCE: how to reset image unit for C350 bizhub?

well there is a chip on the image unit that image unit (all colors) you need special chip writer to reset. you may need to just buy a new unit or drop me a line i may be able to get one...

Posted on Oct 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Konica Minolta bizhub C252 cannot stabilize


Clean IDC sensors that read toner density on transfer belt.
And do Image stabilise reset.

If that doesn't help then:

If Imaging units are over life -replace them if Transfer belt is over life replace it.

Mar 27, 2017 | Konica Minolta Office Equipment & Supplies

2 Answers

KM bizhub c 203 prints blank on yellow, I have tried replacing the y imaging unit, y laser unit, image transfer belt, all to no avail. How could it be fixed?


Have you tried the High Voltage board that supply the voltage to the print heads and ITB. could be the print head is fine biut not getting any power to fire the laser and write to the drum

Mar 20, 2017 | Konica Minolta Bizhub c203 Copier

1 Answer

After replaced transfer belt unit its error 2152


Open close front door. to reset. Ensure belt was install properly the code is for that device also check the transfer roller sponge one. ensure shipping parts remove before installation.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Jan 31, 2014 | Konica Minolta Konica Bizhub C353 Drum...

1 Answer

Cual es la cinta de transferencia que tengo que quitar para limpiar los sensores de control de densidad de una bizhub 203


replace the black image unit and clean the transfer belt sensors located under the transfer belt

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Nov 23, 2013 | Konica Minolta Bizhub c203 Copier

1 Answer

C13c8


C13C8 A new installation is not detected when a new Transfer Cleaner Unit (Image Transfer Belt Unit) is installed.
When a new transfer belt unit is installed in a machine an internal component on the transfer belt unit changes state; this now indicates that the transfer belt unit is used
http://kmcopierservice.blogspot.com/2011/02/how-to-reset-transfer-belt-bizhub-c203.html

Apr 10, 2012 | Konica Minolta bizhub 350 All-In-One Laser...

2 Answers

Machine status P-9 what is this message?


Black Imaging Unit failure
• All density readings taken from the density pattern produced
on the Transfer Belt are 0.5 g/m2 (IDC Sensor
photoreceiver output) or less during max. density
adjustment (Vg/Vdc adjustment).
• All density readings taken from the density pattern produced
on the Transfer Belt are 4.5 g/m2 (IDC Sensor
Photoreceiver output) or more during max. density
adjustment (Vg/Vdc adjustment.)

Remove and reset the Black Image Unit. If this doesn't help the Image Unit may need to be replaced.

May 25, 2010 | Konica Minolta bizhub C250 All-In-One...

2 Answers

Where can I get instructions on how to replace the transfer unit of my Bizhub C252?


Please visit the site http://www.resetkit.eu
There you can find how to reset your fusing unit and transfer kit unit for almost all Konica Minolta MFP's and printers, Bizhub C252 included.
You don't need to replace it, you can just reset it and save a lot of money.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

Oct 22, 2009 | Konica Minolta bizhub C250 All-In-One...

2 Answers

I have a C6500 and it has a 2220 code


C-2220 When the transfer belt motor
(M18) was ON, M18 abnormality
detection signal was continuously
detected for the specified
time.

solution
Printer control board (PRCB)
Transfer belt motor (M18)

Dec 19, 2008 | Konica Minolta bizhub C250 All-In-One...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...