Konica Minolta Office Equipment & Supplies - Recent Questions, Troubleshooting & Support


model number would help

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered 3 days ago


need a developer or turn off press stoop button and turn on :) (it's a truble reset )

Konica Minolta... | Answered 3 days ago


if u installed ADF on Ur machine then check the ADF feeders if not .. then check scanner Assembly

Konica Minolta... | Answered on Apr 20, 2019


he KIP 3000 is a single footprint Multi-Function Printer which can copy, scan and ..... In case the following Error Codes for a serious failure appear in the screen;.

Konica Minolta... | Answered on Apr 20, 2019


you just turn it off at the main switch (or unplug from the outlet), wait 10 seconds and turn it on to reset the temporary user initiated lock out.

  1. if the tray cannot be opened the emergency open latch is via a hole on the rear of the large capacity tray. stick in something till you feel the lever, push it and the tray should open. If the tray for some reason (usually user error) has lifted all the way up and the drawer cannot open, well, your going to need a technician and an open checkbook.

Konica Minolta... | Answered on Apr 20, 2019


9272927292729272

Konica Minolta... | Answered on Apr 20, 2019


To avoid electrical shock, do not open the cabinet. ... Take out any discs from the tray when you ... Disconnect the AC power cord (mains lead) .... The source code for the software used in this ... Pop-up Menu, or the DVD's menu. .... F Playback information ..... for video-based material will always be.

Konica Minolta... | Answered on Apr 20, 2019


c250 have error codes C-xxxx make and model????

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Konica Minolta... | Answered on Apr 20, 2019


check the assy under the transfer belt that slides above the front and rear id sensors is working, the arm can snap so the sensors can not see the belt.

Konica Minolta... | Answered on Apr 20, 2019


Code

C-2302

Description

The EM signal shows an abnormal condition when a specified period of time elapses after the cleaner cooling fan (FM5) turns ON. This abnormal condition recurs when a specified period of time elapses after FM5 is turned OFF and then ON again.

Causes

Cleaner cooling fan (FM5) ADU drive board (ADUDB) Printer control board (PRCB)

Konica Minolta... | Answered on Apr 20, 2019


The code indicates that the fuser is not turning for whatever reason.............. Do the following if it resets the code great, if it comes back it's probably the sensor on the fuser that detects rotation I think its PS-47. They have had problems with the mounting plate but at any rate at that point it would be time to call your servicing entity.

1. Turn OFF the main power switch.
2.Turn main power switch ON while pressing the Utility/Counter key. Keep holding it till the T reset appears
3.Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, wait 10 seconds and fire the machine back up, this should reset the service code and with any luck the machine will run!

Konica Minolta... | Answered on Apr 20, 2019


  1. However, minolta-qms, Inc. makes no warranty of any kind including, but not limited ... Image Transfer Roller Cleaning 63 Image Transfer Belt Cleaning Mechanism 64 ... TAKE-UP SECTION 71 Manual Feed Tray 71 Lower Feeder Unit (Option) 72 ... 1 Do not unplug or plug in the power cord, or perform any kind of service or ...

Konica Minolta... | Answered on Apr 20, 2019


Drive system home sensor malfunction
• The scanner home sensor is unable to detect the scanner located at its home position. • The scanner home sensor is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor.

1 Correct or change the scanner drive (cable, pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the connector between M201- REYB/SCAN PJ5 for proper connection and correct as necessary. 5 Check the connector between PS201- REYB/SCAN PJ8 for proper connection and correct as necessary. 6 Check the connector between REYB/ SCAN PJ2-MFPB PJ14 for proper connection and correct as necessary. 7 PS201 I/O check, sensor check REYB/SCAN PJ8-3 (ON) T-9 8 M201 operation check REYB/SCAN PJ5-1 to 4 T-12. 9 Change REYB/SCAN. 10 Change MFPB.

Konica Minolta... | Answered on Apr 20, 2019


Ventilation Fan Motor's failure to turn • The Lock signal remains HIGH for a continuous period of 1.5 sec. or more after the lapse of 10

Konica Minolta... | Answered on Apr 20, 2019


  • The upper limit sensor /1 (PS6) does not turn ON within a specified period of time after the paper lift motor /1 (M7) turns ON.

Konica Minolta... | Answered on Apr 20, 2019


  • As the title says, we have a 190F which shows out of toner. Have replace toner cartridge (often), main board and both sensors that detect toner in the cartridge, has anyone else had this on this lovely machine!

  • Every new toner contains a little fuse (it is under two tiny contacts). When the user put the new toner into the printer, the fuse blows and the printer detects in this way that it has a new toner in; so if the toner has been for any reason only a moment into the printer cannot reset the message of add new toner.
  • You can test the continuity between the contacts.
Solution A: put in a brand new toner and use the other(s) first of the natural end (so the message is not yet displayed)
Solution B: find a pico fuse of the same value and put it place. (if you are a tech you know the value, it the same in fuser or TBU ). Aldo

Konica Minolta... | Answered on Apr 20, 2019


try pull up error

Konica Minolta... | Answered on Apr 20, 2019

Not finding what you are looking for?
Konica Minolta Logo

12,312 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6830 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...