Culligan Measuring Tools & Sensors - Recent Questions, Troubleshooting & Support
What is an E3 code on a Culligan Medalist Series?
https://www.manualslib.com/manual/859287/Culligan-Medallist-Series.html?page=8
Quoting from link to free manual shown:
FAILURE MODE
There are certain conditions that can be interpreted by the circuit board as a failure of the drive motor or motor
position switch. Upon failure detection the control will cease further operation. A telephone hand set symbol will be
shown in the upper left corner of the display and the error code will be shown. Listed below are the different error
codes.
1. Motor Always Turning
Error code "E1" occurs when the circuit board detects changes in the motor program switch when the motor is
not supposed to be turning. The phone icon and "E1" will be lit in the display.
2. Motor Never Turns
The Culligan Medallist Series control is equipped to detect no change in the motor position when the motor is
supposed to be turning (motor or piston locked in a frozen position). The AccuSoft circuit board will apply
power to the motor for 20 seconds. If there is no change in the motor homing or position switch, the control will
power down for 1 minute. The circuit board will repeat this procedure two more times in an attempt to remove the
obstruction. If no movement has been detected, the control will permanently power down and a phone icon and
an "E2" will appear in the display.
3. Homing Error
Error code "E3" occurs when the circuit board detects when the control is unexpectedly in the home position.
The phone icon and "E3" will be lit in the display.
Error Display Cancellation
The error code display can be removed by removing the power to the control for 1 minute. After clearing an error
condition, the control will default to the factory settings when power is restored.
7/18/2021 2:46:35 PM •
Culligan...
•
Answered
on Jul 18, 2021
How do you change the filter to a culligan water
Here are instruction to remove the filter housing. This is from my tips posting. Culligan filter housings are just Pentek/Pentair water filter housings and these tips apply to virtually any filter housing. Frequently whole house filters can be very difficult to remove. The
canisters become almost impossible to loosen, even after pressing the
pressure relief valve and using a housing wrench. The most common
reasons for this are the housing was put back on with the housing
wrench, debris in the housing threads and a bad pressure relief valve.
How to remove a stuck filter housing.1. Turn off the incoming water. 2. By-Pass the Softener3. Go to the nearest cold water faucet, open it and let the water run until pressure drops significantly.4. Turn the water off at outlet of filter (If housing has shutoff on top off head, turn this off now).5. Press and hold the pressure relief button to relieve pressure further.6. Use filter wrench to unscrew housing (If it still won't loosen repeat steps 2-5).7.
After removing, clean housing thoroughly, make sure threads are clean
on filter bowl and housing head. Lubricate threads of housing and head
with plumbers faucet lube or silicone. 8. Clean and lubricate the
O-Ring (replace the O-ring every couple years or if housing leaks after
screwing back on). It helps to flip the O-Ring over a couple times per
year. 9. Replace the cartridge filter and screw the housing back on. 10. Turn the incoming water on slowly while holding the pressure relief button down until all air is purged.11. Open outlet and let water run to cold water faucet until all air is purged.12. Put softener back in service.IMPORTANT! Only tighten the filter housing by HAND! NEVER use the housing wrench to tighten the housing. I hope these tips help you with the angst of removing stubborn filter housings.RJ
7/10/2018 7:21:01 PM •
Culligan...
•
Answered
on Jul 10, 2018
How often should my softener regenerate
the regeneration period is set on the water consumption
after a set amount of water is used , it should regenerate automatically
use quality water filters prior to the softener to remove mud and particles that all affect the regeneration process
regeneration is the process of removing the elements that have been collected in the machine and to replenish the salt content in use
9/7/2017 11:38:14 PM •
Culligan...
•
Answered
on Sep 07, 2017
Not finding what you are looking for?