20 Most Recent Sunpentown WC-30U Under-Counter Wine & Beverage Cooler 32-bottles NEW - Page 7 Questions & Answers


Hi!

Usually it is just the jet in the carb that needs changing in most High Altitude kits. To change this remove the carb bowl at the bottom. Remove the float and float needle (be sure if there is a spring not to loose it!) Then the jet will be visible where the float needle was sitting. Remove and replace with your new jet.

If you need help moreg let us know. We have a whole Help Center dedicated to helping people fix their Portable Generators and Engineers who can advise you. Check it out on our site. https://www.generatorguru.com/

Parts Spares for Generators and Small Engine Machinery
image-2fwsrbehqcya13uxwt41l5dc-1-0_3.jpg

Electrical... | Answered on Aug 19, 2019


Here is the solutions for your question:

1. Measuring whether there is real electricity, the generator replaces the voltmeter.
2. Put it into automatic or manual mode.
3. Check and correct according to the circuit diagram.
4. New generators or machines that have not been used for a long time appear easily. They can be charged by charging buttons on the control screen or by 12V batteries. The positive pole is connected to F1 and the negative pole is connected to F2. If the voltage can not be established, the positive and negative poles of the batteries can be changed and retried.
5. Cleaning is the surface of the ring. The end surface of the carbon brush is sanded so that it coincides with the arc on the surface of the collector ring more than 70% and the spring pressure is strengthened.
6. Clean carbon brush and carbon brush grip make carbon brush move freely.
7. Check the forward and reverse resistance of the diode with the multimeter, such as damage and replacement.
8. Use a multimeter to check if the forward and reverse resistances do not meet the requirements of diode characteristics. If the resistance value is infinite, the multimeter 1K for diesel generator sets should be turned on. Then use one Eurometer to check if the resistance value is zero, replace or handle the windings. If the resistance value is not stable, check whether the connection of the joint is loose.

https://www.dieselgeneratortech.com/generator-set

Electrical... | Answered on Aug 19, 2019


Here is the solutions for your question:

1. Measuring whether there is real electricity, the generator replaces the voltmeter.
2. Put it into automatic or manual mode.
3. Check and correct according to the circuit diagram.
4. New generators or machines that have not been used for a long time appear easily. They can be charged by charging buttons on the control screen or by 12V batteries. The positive pole is connected to F1 and the negative pole is connected to F2. If the voltage can not be established, the positive and negative poles of the batteries can be changed and retried.
5. Cleaning is the surface of the ring. The end surface of the carbon brush is sanded so that it coincides with the arc on the surface of the collector ring more than 70% and the spring pressure is strengthened.
6. Clean carbon brush and carbon brush grip make carbon brush move freely.
7. Check the forward and reverse resistance of the diode with the multimeter, such as damage and replacement.
8. Use a multimeter to check if the forward and reverse resistances do not meet the requirements of diode characteristics. If the resistance value is infinite, the multimeter 1K for diesel generator sets should be turned on. Then use one Eurometer to check if the resistance value is zero, replace or handle the windings. If the resistance value is not stable, check whether the connection of the joint is loose.

More solutions from the website:
https://www.dieselgeneratortech.com/

Electrical... | Answered on Aug 19, 2019


If so, maybe the oil float is broken.Suggest you to check the oil float.

If you need other brand diesel generator set or learn more about solutions for other faults of generato, please visit at: https://www.dieselgeneratortech.com/

Electrical... | Answered on Aug 19, 2019


Hello, did you try to contact your generator supplier to get the solutions? If not, here is some suggestions to you:
Try to find wthat is the cuases of generator stop.
Generally speaking, the design of sound and light alarm is not allowed to eliminate the light alarm artificially. Sound can be artificially eliminated, and light can never be artificially eliminated.
Because the signal of the light alarm comes from the sensor, when the fault disappears, the signal of the sensor will disappear and the alarm light will also be extinguished.

Cummins, Perkins, Volvo, Deutz, Wechai, Yuchai, Shangchai etc. diesel generator set specification:
https://www.dieselgeneratortech.com/generator-set

Electrical... | Answered on Aug 17, 2019


dead batteries will show 1 volts until a load is placed on them then they drop to 9 or less
test the battery using a load tester and replace it if it doesn't hold at least 10.5 volts under load

Electrical... | Answered on Jul 27, 2019


With water running, drop a few ice cubes down the disposal.

Electrical... | Answered on Jul 19, 2019


Anything plugged into it? A Surge protector can cause this.

Does the generator require you connect the gender to ground from a lug on the side? It may be expecting this.

It really depends on what load is connected.

If theres no load connected (gen only) call customer service.

Electrical... | Answered on Jul 13, 2019


These outlets give trouble sometimes. Check if there is voltage in the outlets if not check the main switch.

Electrical... | Answered on Jul 12, 2019


Bad Switch or No Power? is it a light?

Electrical... | Answered on Jul 10, 2019


Please send me the GFCI brand in question and the amperage, example 15A or 20A. If you can send me a picture that would be an added bonus!
I am a 30 yr Master Electrician in Seattle https://benchmarkseattle.com/electrical-services

Electrical... | Answered on Jul 10, 2019


Not likely to be DC generator output, it has inverter output. Inverter converts dc to ac. Test it if you have access to a voltage meter.

Electrical... | Answered on Jul 06, 2019


I would start by checking the power supply in it for a dead short, broke down diodes, foreign objects causing shorting.
What circuit breaker of yours are you referting to, the unit's or the house power?
With a little luck you can repair it once you test components.

Electrical... | Answered on Jul 05, 2019


Any power supply will work as long as it is 125% of the load.
Conductors, extension cords must be sized accordingly as to avoid voltage drops or power loss to undersized cords or conductors.

Electrical... | Answered on Jul 05, 2019

Not finding what you are looking for?
Sunpentown WC-30U Under-Counter Wine & Beverage Cooler 32-bottles NEW Logo

4 questions posted

Ask a Question

Usually answered in minutes!

Top Sunpentown Electrical Supplies Experts

rlev_7

Level 1 Expert

47 Answers

John Trevino

Level 3 Expert

1420 Answers

wadingriver
wadingriver

Level 3 Expert

2223 Answers

Are you a Sunpentown Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sunpentown Electrical Supplies

  • Sunpentown Electrical Supplies

Most Popular Question

put handle

  • Electrical Supplies
Loading...