Ariane alarm how to reprogram remote control of ariane car alarm system?

go to google! or the parts dept where you got the remote they have instructions for it there

Go to www.youtube.com and watch this short video. It will only take you a minute to program each key fob.

https://www.youtube.com/watch?v=uOXUIfddHBU

1. Cars
2. Car Maintenance
3. General Car Maintenance
4. How to Program Keyless Entry Remotes in a Hyundai Sonata

How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor

• ? Pin
• ? 9
• ? Tweet
• ? Stumble
• ? Share

20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading

• How to Reprogram Key Fobs Yourself
• How To Replace a Hyundai Sonata Remote

Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links

• Download New VersionSnagit 12 Image & Video Capture. Edit & Share. Try Free Today!
  techsmith.com

Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.

Here are some factory notes....FYI

Anti-Theft Systems

PROGRAMMING

NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.

PROGRAMMING > PROGRAMING NEW ID CODE

NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.

Please let me know if you need anything else to get the problem fixed. Happy mew Year!

check your manual for remote programming. may have to reprogram remote control or leave car running so it can all reprogram to factory settings

there is no way that i know of to rest the alarm and remote entry system it most likely needs to be reprogrammed and this can only be done at a dealership

The best thing to do is:

1- Replace the battery that is located on the back of the remote. If nothing happens then;

2- Try reprogramming the remote control with the car. if you have the original manuals, then it will precisly tell you how to reprogram your remote to successfully communicate with the alarm module in the car.

The problem could also be the Alarm module receiver.

hope that helps. Let me know.

if its the remote then it needs to be swapped out. it could be the alarm module if the remote is not the thing that malfunctioning. i would get the alarm reprogrammed by the dealer and the whole module and go from there.
so in order, 1. reprogram whole system 2.replace remote 3.replace module

is the alarm after market ? and is so you need to replace it with another after market one .. now if the alarm is factory ?...you will need a remote control from the dealer and they will reprogram it for you