Top 10 2000 Chrysler Grand Voyager Questions & Answers

i had the same problem with my crysler voyager 1997,a friend of mine who is a mechanic found the problem,it is a self adjuster on the handbrake itself,once drums are adjusted up you need to go to your hanbrake area and you will find a white plastic clip on the bottom of the lever ,once removed you pull up your handbrake a few times and it self adjusts,then put the plastic clip back on,this soved my problem,by doing this my handbrake went from about 13 clicks on max to hold . to about 6 clicks and held perfectly

In 2000 the only Grand Voyager that was equiped with a cabin air filter was the 6 cylinder 3.3 liter Sport model.

Cabin filters are generally found in one of two locations: under the hood, or under the dash board.

Hey I got a 1998 Chrysler voyager and can not get rid of alarm set point as you said I am on the forum and still do not go if you can help me on [email protected] mail message pretty please

is this the 3.3 liter or the 3.8?

I know that there is 1 serpentine belt that runs all (incl. the PS pump) on the 3.8 liter. So if that belt
was missing, you would also be over heating, have no alternator charging, no ac (if equipped) as well as have no PS. If you see any belt at all (on the passenger side), then you are ok. The PS fluid resevoir is near the top and easily found. It has writing on the cap which also has a built in dipstick. Check the fluid level in the resevoir and fill it if nec. Are you hearing noises from the PS system with the fluids full? If so, you might need a new pump. Check for leaks too if the fluid was low, you might have a leaking hose or PS rack (hope not on the rack though $$)

This is the description about the instrument warnings, and I can identified the warning signal that you send us; maybe is refer to the some "heated"...



Hope helps (remember rated this). Good luck.

Hi,

The steps involved are :-

1. Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

2. Remove the 3 starter motor-to-transaxle bellhousing mounting bolt.

3. Remove the starter motor from the vehicle

4. After removing the starter motor, examine the teeth of the flywheel for excessive wear or damage. Repair if necessary

5. If the old starter is going to be re-installed, check the condition of the pinion gear teeth. Replace the starter if the pinion gear shows excessive wear or damage

1. Disconnect the negative battery cable.
   
2. Raise and safely support the front of the vehicle securely on jackstands.
   
3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
   
4. Remove the B+ nut and wire from the starter motor terminal.
   
5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
   
6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
   

To install:

1. If equipped, hold the starter motor spacer in position.
   
2. Install the starter motor into position on the vehicle.
   
3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
   
4. Engage the solenoid wiring connector onto the starter terminal.
   
5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
   
6. Lower the vehicle.
   
7. Connect the negative battery cable.
   
8. Verify starter motor operation.
   

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

PS - Do accept this solution,if it has been of any help so that i could get the credit for my time.

ANY ONE HELP LOOKING FOR A HEAT DIAGRAM FOR HETATER CONTROL PANEL ANY ONE HELP WITH COIOURS

If you read the back of any trans fluid bottle, it tells
you what it is for

Chrysler uses ATF+4 in most cases

If you have a drip stick, it should be stamped on it

Owners manual is a must if you own a vehicle &
you can always check with dealer service dept

https://www.google.ca/search?q=Where+is+the+crankshaft+position+sensor+2000+chrysler+voyager+2.4L&hl=en&source=lnms&tbm=isch&sa=X&ei=2J82UamUKsPWygHQyoCoBg&sqi=2&ved=0CAcQ_AUoAQ&biw=1366&bih=667#imgrc=CCm04tc9Q6spXM%3A%3BZMusm8em5DHqxM%3Bhttp%253A%252F%252Fc.fixya.net%252Ffixya20%252Fuploads%252Fimages%252F10_14_2011_2_00_35_pm.gif%3Bhttp%253A%252F%252Fwww.fixya.com%252Fcars%252Ft10666937-want_change_oil_ina_2_4_l_chrysler%3B309%3B300

It comes out of the firewall on the passenger side. Near the bottom. It will just be a tube pointing down.