20 Most Recent 2006 Dodge Caravan Questions & Answers

The P0340 code indicates a problem with the camshaft position sensor circuit. However, given the additional symptoms you've described, it's possible that there may be multiple issues contributing to the no-start condition. Here are a few things you may want to check:

1. Check the wiring and connector for the camshaft position sensor. Make sure the wiring is not damaged and the connector is securely attached.
2. Check the timing belt or chain. A broken or worn timing belt or chain can cause the camshaft position sensor to fail and can also result in a no-start condition.
3. Check the crankshaft position sensor. A failed crankshaft position sensor can also cause a no-start condition.
4. Check the fuel pressure. While you can hear the fuel pump activate, it's possible that it's not delivering the proper pressure to the fuel injectors.
5. Check the ignition system. Check for spark at the spark plugs and make sure the ignition system is functioning properly.
6. Check for vacuum leaks. A vacuum leak can cause a rough idle or a no-start condition.

It's also possible that the excessive oil on the spark plugs may be related to a separate issue such as a failed piston ring or valve seal. If you've checked all of these components and are still unable to diagnose the issue, I would recommend taking your vehicle to a qualified mechanic who can perform additional diagnostics to pinpoint the cause of the no-start condition.

What are the torque specs for the rod bearings on a 2006 - Fixya

https://www.fixya.com > ... > 2006 Dodge Caravan Nov 15, 2019 - What is the torque specification for the inner tie rod 1996 .dodge caravan 2.4 liter. 45-55 foot pounds. Read full answer. Sep 18, 2012 • 1998 ... SOLVED: Torque chart for dodge caravan 4l - Fixya Sept 9, 2019 Main bearing torque spec for Dodge Grand Caravan 2005 Sept 15, 2019 Im trying to find the connector rod bearing torque - Dodge - Fixya Jul 15, 2018 Head bolt torque specs for 2.4L dohc dodge caravan - Fixya Jun 2, 2012 More results from www.fixya.com

Dodge Caravan 2.4 need engine tightening specs and head ...

https://www.justanswer.com > chrysler > 28qv6-dodge-... Jun 27, 2009 - SPECIFICATIONS - TORQUE ; Balance Shaft Carrier Cover-Bolts, 12, - ; Camshaft Sprocket-Bolt, 101, 75 ; Connecting Rod Cap-Bolts, 27 +¼ turn, 20 +¼ ... 1 answer · Top answer: Here are the head bolt specs: Before installing the bolts, the threads should be coated with ...

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3 PDF Engine Model Year. Rod Torque. Main Torque. Cylinder Head Bolt Torque. CASE. 2.4. 148. 61-66. 45-50 FT/LBS. 90-100 FT/LBS. 60-65 FT/LBS. CASE. 2.4. 124 pages You've visited this page 3 times. Last visit: 01/02/22

sounds like linkage disconnected it will be annoying but need to remove panel it can be done but time consuming

U will have to take the inside door cover off and manualy open it. And replace the electric door locking switch. Very common problem. Get the new lock and latch assembly from dealer,

the relay is probably under hood on driver side fuse panel.most dodge has a template on underside of cover

Those two fuses are for front and rear power outlet. As you can see that relay has to be energized to get voltage at the fuses. You can use a test light to check for voltage at the fuses.

On this website you find fuse box diagram and description for Dodge Caravan (2005 - 2007) Dodge Caravan 2005 2007 fuse box diagram

in the fuel tank

Sound like to me the plastic clip on your lock actuator has broken Your Rod has fell down in the door

Some companies will repair a large crack such as your if it does not reach from one edge of the windshield over to another.I would recommend replacement.Most of the time you can see the crack slightly still after the repair and delamination is a possibility later on.check with your insurance company and you may be able to pay a $50 deductible to have it replaced.

My suspicions are that the BCM is faulty ????? Before condemning the BCM Suggest you have a qualified repair shop check it out . Doesn't sound like you know a whole lot about automotive electronic's ! We in the profession don't guess ,we test . Hooking up a professional type or factory scanner to see if the BCM will talk with the tool . If it does more then likely nothing is wrong with it . An if it doesn't talk with the scanner ,still doesn't mean it's bad . Finding a wiring diagram an checking power an grounds would be the next step. Checking for DTC'S - diagnostic trouble codes would be another step if the BCM communicates with the scanner . So do yourself a favor before replacing parts you have no clue about ,have a qualified repair shop check it . I only say this because if you knew anything you would view a wiring diagram an test the electrical circuit's for fuse #24 . Seeing what all it power's up .I see problems like this daily ,working at Chrysler , dodge ,jeep dealer . An people trying to fix it them self ,make it worst .

dodge and chryslers do this electrical system If you need further help, reach me via phone at https://www.6ya.com/expert/james_9c1b039055413ffa

Do you mean the key switch

sounds like your radio got wet and it might be your windshield that leaks

A single wire or a wire harness ?

U need first of all to check if engine light is on and read out codes to lead U into the right direction if no engine light on check next to see if U have fuel pressure issue might want to start with a new fuel filter if not replaced already after would be a fuel pump assumption need to diagnose step by step to determine a solution this is a hypothetical. Good Luck