Mazda MPV - Recent Questions, Troubleshooting & Support
Remove cup holder ash tray mazda mpv 2004
To remove the cup holder/ashtray in a 2004 Mazda MPV, you can follow these steps:
- Open the cup holder/ashtray and locate the small tab on the right-hand side of the unit.
- Using a flathead screwdriver or other suitable tool, gently press down on the tab to release the retaining clip.
- While holding down the tab, pull the cup holder/ashtray unit towards you to release it from the center console.
- Once the unit is free, disconnect any wiring harnesses or light bulbs attached to it, if applicable.
To reinstall the cup holder/ashtray, simply reverse these steps, making sure the retaining clip snaps back into place when reinserting the unit into the center console.
Como proceder para verificar o problema da luz de injecao no painel da Mazda MPV 1995 (In English: How to go about checking the fuel injection light problem on the Mazda MPV 1995 dashboard)
If the fuel injection light is illuminated on the dashboard of your 1995 Mazda MPV, it means there is a problem with the fuel injection system. Here are the steps you can take to troubleshoot the issue:
- Check for any other warning lights: If there are any other warning lights on the dashboard, it could be an indication of a bigger issue. Check the owner's manual for guidance on what to do next.
- Check the fuel level: Make sure the fuel tank is not empty or low. If the fuel level is low, add fuel to the tank and see if the light turns off.
- Check the fuel injection system components: Check the fuel injection system components, including the fuel filter, fuel pump, fuel pressure regulator, and fuel injectors. If any of these components are faulty, it could cause the fuel injection light to illuminate.
- Check the connections: Check all electrical connections related to the fuel injection system. Loose or corroded connections can also cause the fuel injection light to come on.
- Check the diagnostic trouble codes: If you have an OBD-II scanner, you can use it to check for diagnostic trouble codes (DTCs) that could be causing the fuel injection light to come on. The DTCs will give you a clue as to what the problem is.
If you are unable to diagnose the problem on your own, it's best to take your Mazda MPV to a certified mechanic who can diagnose and repair the issue for you.
Change speedo face on mazda bongo
REMOVE AND REPLACE SPEEDO FACE
How to remove the speedo face
Undo the 4 screws that hold the black cover in front of the speedo. Pull the cover off. Undo the 4 screws that hold the instrument cluster. Lift out the cluster. Disconnect the 2 or 3 mulit-plugs from the back. Remove the black panel that hold the glass (push clips). If you don't have the proper tool, use 2 metal spoons to lift the needle from the speedo face. You use the bowl of the spoons on the needle and press on the handles. (It's easier than it sounds.) Undo the 2 screws that hold the speedo face on. Lift it off. Fit the new face.
How to zero the needle on a new speedo face
Fit the speedo unit (without the glass) back into the dash, with all wires connected into the back of it.
Don't fit the needle-stop post to the speedo face yet.
Switch the ignition on. Fit the needle in the zero position.
Now fit the stop-post and glass.
I cannot turn my key
There is a small microswitch on the change lever assembly that has failed. This switch is used by the key interlock system to detect shift lever being put into Park position. The microswitch has not been available in the past as an indivfidual part but must be purchased with the entire change lever assembly.
2002 mazda mpv, key stuck in ingition and it is in
2001 MAzda MPV- Key was stuck in ignition. Would not turn all the way back to remove. I pulled the fuse for the Hazards and WHOLA!! Key turned back and could be removed.! Just to test the problem I put the key back in , started up , pulled up and back a few feet, turned the steering wheel and parked. Key was stuck again. I pulled the fuse and again ... WHOLA! key was released. Now what I need to do is fix the problem or I have to pull a fuse every time I stop the car - ANY ADVICE??
Where is the location of ac expansion valve on 2002 mazda
On a 2002 Protege, you access the expansion valve by removing the glove box and the evaporator case on the passenger side. Two ac lines are disconnected in the engine compartment, two bolts and two electrical plugs and the evaporator case slides out.
Radio not working
use a multi meter to check for power /shorts to the unit/circuit ---looking is not testing
I just got a 2000
are you asking why it won't change into dd or why won't the shifter go to lower gears?
Not finding what you are looking for?