Hi my Kelvinator kd12 ww1 is a month old. Yesterday we had power failure while the machine was on. The intensive button flases the hole time but nothing is happening. if you press start/pause button nothing happens. if you switch it on and off it beaps a couple of times flashes intensive button and does nothing

Question edited for clarity.

No model number provided. Some generic help here.

https://www.google.com/search?q=kelvinator+dishwasher+machine+replace+temperature+sensor

..

Hi,

There is air in the lines and it is blocking the water flow...
Here is a tip that will help you getyour Keurig to prime...

Keurig CoffeeBrewer will not prime
heatman101

Hi
There is a filter located in the pipe between the connector to the water outlet and the machine, This sometimes gets clogged. If this dos not solve the issue then time to call a tech. Anyway your machine is just 7 months old and it should still be in the warranty period and the service should be free.
Regards.
PLZ. don't forget to rate my suggestion.

My EWD1477 was doing this a year ago and I fixed it. Then it started doing it again a month ago and I seem to have cleared it again.

Firstly, remove the drain hose from where it is inserted into a laundry sink hole to make sure it is not blocked or sealed in with sludge.

Secondly, make sure the machine is empty of water and clothes and then turn the machine to off with the Program Selector Dial. Then turn off the power at the socket and remove the power plug and leave for five minutes.

Step 1: put the plug back in and turn the power back on.

Step 2: turn the selector switch to the right (Whites/Intensive). The green light of the Start/Pause button should be flashing and the green lights on for Prewash/wash, Rinses and Spinning. Don't press any other buttons or change any other settings.

Step 3: press the Start/Pause button and wait for the machine to empty any excess water. Press it again immediately after you hear water flowing into the machine OR two audible clicks. The machine is now in pause mode with the green light of the Start/Pause button flashing. Only the green light on the Prewash/Wash button should be on. Leave it in pause mode for 30 minutes and then press the Start/Pause button to recommence the cycle.

Step 4: If the Start/Pause button begins flashing, water stops flowing into the machine and the three green lights mentioned above are back on, turn the Program Selector Dial back to off, wait 10 seconds, and repeat the process above.

Step 5: If when you then turn the Program Selector Dial to Whites/Intensive and hear the two audible clicks, immediately press the Start/Pause button to set the machine in pause mode. Wait 30 minutes. Then press the Start/Pause button to recommence the cycle.

Hopefully the cycle will run without a problem.

I have a smart drive 708 that will turn on but won't fill, any suggestions?

press function and f5 at the same time

www.diplodocs.com



Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

check the lid switch under the lower board they rust and the fault is normally not starting,or the display board can rust inside near the start/pause button if so try and unsolder a button you dont use and replace the start button.

If the milk scalds, you're getting it hot enough. It sounds like you're not incorporating enough air into the milk when frothing.
Make sure that the holes in the tip of the steam wand are clear. Soak in water for 5-10 min. and wipe with a cloth (no abrasives) and clear the holes with a paper clip end. Blow the wand out nice and hard.
How is your steam pressure? It should be about 1.2 bar.
It could also be your technique. The wand should never be more than 3 cm into the milk. For cappuccino froth, keep the tip right at the surface of the milk, lowering the pitcher as the level rises. You should hear a "shushing" sound, no squealing.

Good luck!