I am getting a flashing message E5 where the temp is normally displayed on my U-Line Beverage Center. I could not find info in the manual on this code?

Do you have base instrument cluster) or high series instrument cluster) ?
Symptom Chart Condition Possible Sources Action

• The message center is not operating correctly (base instrument cluster)

• Instrument cluster

• OBSERVE the operation of the message center when pressing the TRIP/SELECT button. Does the message center display change when the TRIP/SELECT button is pressed?
  • If the message center display changes, the system is operating normally at this time.
  • If the message center display does not change, INSTALL a new instrument cluster. REFER to Section 413-01 . TEST the system for normal operation.

• The message center is not operating correctly (high series instrument cluster)

• Message center switch
• Instrument cluster

• Go To Pinpoint Test A .

The temp lights might indicates the actual temp settings havent reach the programmed settings. If its on and off coz it try to recover the temp lose after it drop below prog. Temp. Monitor it first if its cooling must be normal only.

If you are winding the bobbin in the middle of sewing process, it is normal to get a notification (E5) that bobbin winder should be returned to the left position before continuing to embroider.

This normally indicates that the thermistor is bad. Try measuring it to prove it is OK. It should be 10K Ohms at room temperature (20C / 68F).
If necessary, replace it then clear the error code.
1. Enter to Service Mode by press CHIME and TEMPERATURE keys for 3 seconds or until 3 beeps are heard.
2. Access Diagnostic Codes by pressing WRINKLE PREVENT. A d will be displayed. Rotate the CYCLE SELECTOR KNOB in either direction to read it.
3. Press SENSOR DRY and TIME keys for 3 seconds to clear it.
4. Power OFF to exit Service Mode
5. Power ON

You will need Adobe Acrobat Reader to view these documents. The Adobe Acrobat Reader is available as a free download. Get Adobe Acrobat Reader Click Here=> KUWA244PBS Parts List
and here=> KUWA244PBS User and Care Guide
If you should need the service manual you will need to cant me here=> HERE Reason is Whirlpool does not allow me to publish the SM here.

The beverage center and wine cellars have a temperature display for each zone. 12 volts

AC is supplied to the display board from a transformer in the unit compartment. The displays are only temperature displays and have nothing to do with any cooling function. A thermistor is used to sense temperature for each zone. The thermistor for the bottom zone is located inside the lower portion of the separator. The thermistor for the top zone on the wine cellar, (mid zone on beverage

center), is located in the upper portion of the separator. The thermistor for the beverage center upper zone is located on the inside of the 2-piece evaporator cover. It is on the right-hand side.

The mid temperature for the bottom zones on either unit are 60? Fahrenheit plus or minus 5 degrees. The mid temperature for the mid zone on the beverage center and the top zone

on the wine cellar is 45? Fahrenheit plus or minus 5 degrees. The mid temperature for the

top zone on the beverage center is 38? Fahrenheit plus or minus 5 degrees. I think at tis time you should check each section with a pocket size digital thermometer to cofirm tha the mechanical thermostat is within calibration. Click Here=> 4344690 Temperature Control

Click here for a=> KUWA244PBS Beverage Center Wiring Diagram
I believe the problem may be in the PCB transformer shown at the bottom right corner of the wiring diagram. It is possible o change the transformer but I have not been able to find the board that powers the LED temperature readouts. If needed let me know and I will call Whirlpool mfor you, Thanks, Sea Breeze

Wow if you have lost that much because the memory dumps during a power failure then we are going to need do something serious about that! May take me a while to come up with a solution but being the case I think you have a serious point to make. Acording to The

Frigidaire FFBC46F5LS Beverage Center User Manual

and on page 7 of the PDF

The default temperature for the beverage cooler is 41°F (5°C). The temperature after power failure will be the temperature set before the power failure. So something is wrong with the control board part=> Pc board,input ,display I believe I would call USA 1-800-944-9044 and ask why that may be happening. Below is a parts list.

Frigidaire FFBC46F5LS Beverage Center Parts

Need Adobe Reader? Click Here=>

Hope this helps, Thanks, Sea Breeze

Hello, I followed your instructions, hold the up arrow and at the same time press and release the light bulb 3 times and then up arrow to 3, got the Er codes E3 and E5, now I'm trying to do the last step to go back to refrigeration cycle and it doesn't work. Help?

check the thermostat for proper setting, evap could be frozen up, the condenser fan could not be running, unit could be low on freon. start check some items and let me know.

Ok what you need to do is call your local service company and have a technician come out and check your Thermostat, its currently not able to read humidity probably due to a power surge

I have the same error on my U-Line beverage refrigerator. U-Line said the error indicates the thermostat was out of range for over 12 hours (perhaps due to a recent power outage). My fridge seems to be working just fine so I am not planning on calling a technician until something more serious breaks down.