How I can change the cleaning brush fo an Ilco 040 Hd authomatic

The plug gap is most likely .040, however can you please confirm your serial number?

the bios is already on the board,
when you are booting the computer you have to push down on the F10, if that doesnt work than try F1 and thanF2, every time you try to enter the motherboard bios you have to start from a cold boot.
website for motherboard bios configuration and settings is at
http://www.msicomputer.com

if you want a copy of the bios setup and configurations and everything explained in detail go to your browser and type the following information.

MS-6758-040 BIOS MANUAL OR
MSI MS-6758-040 BIOS MANAUL

the bois controls everything the that runs you computer, video, ram, HD, CPU, PORT FUNCTIONS, BOOT SEQUENCE, SMART FAN CONFIGURATION, HD CONFIGURATION, TEMP. SETTINGS, AND ALOT MORE STUFF AND VERY LONG LIST.

MAKE SURE THE BATTERY IS MIN. 3VOLTS

You will find installation manuals on this page:
http://www.kaba-ilco.com/kaba-access-control/Documentation-Support/292720/simplex-mechanical-pushbutton-locks.html
You may need to install Adobe reader if you cannot view the documents. There is a "Get Adobe Reader" link found just above the chart if you can't.

Customer service can be contacted from this link:

http://www.kaba-ilco.com/access_control/support_contacts/service_and_support.aspx

Tech Support from this link:
http://www.kaba-ilco.com/access_control/support_contacts/technical_support.aspx

Yours is an unusual problem. Therefore, I suggest that you call Kaba Ilco during regular business hours for assistance. Toll free: 800-849-8324 Be sure to have the model number and any other pertinent info on your lock ready if you call.

On the net:
Customer service can be contacted from this link:

http://www.kaba-ilco.com/access_control/support_contacts/service_and_support.aspx

Tech Support from this link:
http://www.kaba-ilco.com/access_control/support_contacts/technical_support.aspx
1-800-849-8324 (option 3, and then option 6)

Good luck--and please provide feedback if this helps!

I can't help you directly, but I will steer you to further information.
You will find a link to download the manual for your model on this page:

http://www.kaba-ilco.com/access_control/literature/literature_grid_mechanical_pushbutton_locks.aspx?id=13

These are PDF files, requiring Adobe Reader to open. There is a link on the same page to download Adobe reader.

Customer service can be contacted from this link:

http://www.kaba-ilco.com/access_control/support_contacts/service_and_support.aspx

Tech Support from this link:
http://www.kaba-ilco.com/access_control/support_contacts/technical_support.aspx

Good luck!

this is the part for the belt, 38528036. you can get it at sears website or service center. also make sure you clean the caps on the side of the brush. take them out and remove hair and dirt. put a little or mineral oil and install them back.

good luck to you.

Yow will find a link to download the manual for your model on this page:

http://www.kaba-ilco.com/access_control/literature/literature_grid_mechanical_pushbutton_locks.aspx?id=13

These are PDF files, requiring Adobe Reader to open. There is a link on the same page to download Adobe reader.

Customer service can be contacted from this link:

http://www.kaba-ilco.com/access_control/support_contacts/service_and_support.aspx

Good luck!

Customer service can be contacted from this link:

http://www.kaba-ilco.com/access_control/support_contacts/service_and_support.aspx

Tech Support from this link:
http://www.kaba-ilco.com/access_control/support_contacts/technical_support.aspx

You need to replace the belt that turns the brush.

http://www.kaba-ilco.com/access_control/literature/literature_grid_mechanical_pushbutton_locks.aspx?id=13

i have just downloaded user manual from this site hope it solves your problem