Top 20
Samsung SCX-3400 All-in-one Laser printer SAMSUNG Questions & Answers
Scx 4021s toner reset
for scx 4021 , uses scxd4725a toner , cover the toner chip with tape , else replace chip
Printer not printing
first your printer driver correct version install ,then check after samse probelem you must replace the data cable then check after samse problem shuarly your printer formatter card complaint please replace the formattercard try it
Orange light on the samsung printer indicate what?
Toner powder level is too low in the cartridge, you may refill the toner powder in the cartridge with a Samsung compatible toner(not made by the Samsung), or an option to replace the cartridge with a Samsung's MLTD 101 S genuine toner.
Paper doesn't pick up
Check the feeder roller inside the printer for any foreign substance stuck to the roller, this may cause it not to grip properly. You can also try a few sheets at a time and make sure the paper tray is gripping the paper, but not too hard. If this fails, the roller may be out of place somewhat, try to reposition it. Let me know how you get on.
Samsung scx-3400 keeps changing ip addresses
Depends on the router you have. Some routers you can set what they call a DHCP reservation for your printer. I'd like to give you specific instructions but it varies by manufacturer and some home/home office routers don't have the feature. Probably the easiest way if that isn't an option is to set the IP address on your printer to a static address. Then on your computers edit the hosts file in C:\Windows\System32\Drivers\etcAdd an entry to your hosts file for your printer. Your PC will now ALWAYS know the IP address to the printer.Note: On windows 7 you may have to open an administrative command prompt to edit the hosts file. Is usually write protected for security reasons.
I could not samsung scx 3400 printer to my pc having 256 MB RAM
I suggest you install more RAM and do a hard disk maintenance before you install the printer driver. Hard disk maintenance should be carried once a month to make your computer run efficiently. This removes redundant and temporary files,
recovers disk space and speed up hard disk access. Disk Cleanup should be done first - Click My Computer - then right click on the C drive then click Properties, then click Disk Cleanup - let it examine the C drive then it will calculate the amount of disk space it will recover, tick all the boxes to recover the maximum disk space and then Click OK and then Yes to perform these actions. If you have a D drive then repeat these steps on this drive too. Next the C drive needs to be
Defrag. This process converts fragmented files into continuous files and this speeds up disk access and makes the hard disk not work as hard. Click on Start - All Programs - Accessories - System Tools - Disk Defragmenter - click to highlight the C drive and click Analyse - then click Defragment. When this is completed repeat these steps for the D Drive if you have a D drive. Disk Cleanup and
Defrag can take a long time to complete, especially if these tasks have not been for a long time. http://www.fixya.com/support/r3559146-hard_disk_maintenance
Can't reset double sided printing to single side only as default
Exact same problem... took a couple of hours of fiddling but seems that to get it to stick you have to change the printer settings in windows rather than when you are actually printing a document. eg Control Panel > Printers > right click printer > Properties > (General tab) Printing Preferences > then for Double-Sided Printing select 'none' and press OK. Job done.
HOW TO UNLOCK THE SCANNER
Dear
You have not mentioned the model no. However certain model of SCX (viz-5315,6122 etc.) has a scanner lock bellow the platen body. That might have locked.
Other has no locks, since no movement of CIS(scanner) results scanner lock. Mostly the platen cover and the scanner assy. realigned solve this problem. Also in case of small A4 SCX printer, slightly knock with your palm at both side of platen may sometimes over come the problem, make sure after your try machine should OFF and ON.
if the above are not working, then the printer needs hardware replacement may be, scanner drive motor or Main PBA.
Thanks.
Has a lsu error
Dear Ian
Pl. open the LSU and clean the optical path and polygon motor with a dry cotton lint free cloth. If not resolver then replace the LSU.
Thanks.
Not finding what you are looking for?