Your productivity is my business.
John Trevino posted an answer for this Air Tools & Compressors:
"The Square D pressure switch is set from the factory to turn off at about 130 psi. Look..."
John Trevino posted an answer for this Air Tools & Compressors:
"The trigger valve should release air when depressed. This release of air comes from..."
John Trevino posted an answer for this Honda Air Tools & Compressors:
"Your compressor is made by Hitachi. The pilot valve is what controls the engine and the..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"Try lubing the head valve orings with white grease instead of oil. The issue is caused..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"I find that a nailer will fail to discharge due to lack of lubrication. Try lubing the..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"This usually occurs when the check seal is out of place or bent driver or driver is too..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"This usually occurs when the head valve is worn, cracked or just needs lubrication. If..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"This happens due to lack of lubrication. The air that runs thru the regulator is very..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"This happens when the driver is not returning to top of the cylinder. Remove the driver..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"I find that the trigger valves in these guns are reliable and that most problems with..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"The fr350a is completely different from fr350. The fr350a is completely modernized ..."
John Trevino posted an answer for this Porter Cable Air Tools & Compressors:
"The part that you are looking for is most likely the "piston stop." this part can be..."
John Trevino posted an answer for this Air Tools & Compressors:
"I have not been able to purchase replacement parts for these nail guns , however, have..."
John Trevino posted an answer for this Hitachi NR65AK Round Head 1-1/2-Inch to 2-1/2-Inch Positive Placement Nailer:
"Easy to remove the cylinder and piston/driver. Remove four head bolts and lightly tap..."
John Trevino posted an answer for this Hitachi EC12 Portable Electric 2hp Air Compressor, Oil Lubricated:
"The head pressure is released thru the needle unloader valve at the pressure switch. ..."
John Trevino posted an answer for this Hitachi Air Tools & Compressors:
"This problem is usually caused by reed valves or blown gasket between head and valve..."
John Trevino posted an answer for this Hitachi EC119SA Twin-Stack Air Compressor with Control Panel and Couplers :
"The pressure regulator can easily be replaced by removing the large plastic decorative..."
John Trevino posted an answer for this Hitachi Reset Button:
"The reset button is located under the cover visible from the dipstick side of the pump,..."
John Trevino posted an answer for this Air Tools & Compressors:
"My Emglo Air-mate manual calls for 8 oz of oil. Most all of the smaller compressors use..."
John Trevino posted an answer for this Air Tools & Compressors:
"Easy to check trigger valve on Paslode 350s. Just connect air pressure to the gun and..."
John Trevino posted an answer for this Dewalt Air Tools & Compressors:
"The seal # 390140-00 installed on the upper part of the cylinder will allow air to come..."
John Trevino posted an answer for this Dewalt D55153 1.1 HP Continuous 4 Gallon Electric Hand Carry Compressor:
"The issue of low pressure that you experience is usually caused by air leaking from ..."
John Trevino posted an answer for this Dewalt Air Tools & Compressors:
"Air leaking out the nose is indication that the orings at the bulkhead are leaking or the..."
John Trevino posted an answer for this Dewalt Air Tools & Compressors:
"I do not have a picture, but maybe I can describe how to assemble. The rear of the..."
John Trevino posted an answer for this Air Tools & Compressors:
"Max roofing nailers and other brands will have this problem if the feed spring is weak or..."
John Trevino posted an answer for this Air Tools & Compressors:
"Some of these compressors have a thermal breaker tied to the field winding. Most likely..."
John Trevino posted an answer for this Craftsman Air Tools & Compressors:
"This compressor has a 33 gallon tank and a 3 to 5 hp (rated)motor. Sears , however,..."
John Trevino posted an answer for this Air Tools & Compressors:
"A nailer will misfire if the next nail cannot advance to proper position. Make sure that..."
John Trevino posted an answer for this Air Tools & Compressors:
"Many nailers and staplers do not have an adjustment for how deep the nail will drive. ..."
John Trevino posted an answer for this Campbell Hausfeld Air Tools & Compressors:
"This fault indicates that there is too much back pressure on the pump causing the motor to..."
John Trevino posted an answer for this Air Tools & Compressors:
"I have seen many p/c compressors equipped with a thermal fuse attached directly to the..."