joe_jochoa posted an answer for this Lincoln Welding Tools:
"If the cooling fan motor comes on and the the machine “clicks” when you close the trigger,..."
joe_jochoa posted an answer for this Miller Welding Tools:
"Also check to ensure your air compressor is able to supply the recommended CFM that Is..."
joe_jochoa posted an answer for this Welding Tools:
"Your loss of arc control is probably being caused by a PCB failure, usually the control..."
joe_jochoa posted an answer for this Hobart Welding Tools:
"Check your ground connection"
joe_jochoa posted an answer for this Hobart Champ 4500 Welder/Generator Outfit 140 Amp Ac, 4500 Watts:
"Ensure your engine is in good running condition The auto idle switch should function..."
joe_jochoa posted an answer for this Panasonic PT-DW5100U Projector:
"First: what are you attempting to remove the armature from?"
joe_jochoa posted an answer for this Welding Tools:
"The black lead is connected to the metal you are attempting to weld, it has the silver..."
joe_jochoa posted an answer for this Honda Electrical Supplies:
"This an interesting request, I offer the following addition to the previously posted..."
joe_jochoa posted an answer for this Gentron GG10020 10,000w Electric Start Wheel Kit:
"Is this something you have done before, if you connect a generator to your home, You must..."
joe_jochoa posted an answer for this Miller Electrical Supplies:
"kohler engine, 45-50 foot LBS"
joe_jochoa posted an answer for this Miller Bobcat 225 OHV Welder Generator Kohler Gasoline Engine:
"first, make sure your brushes are making good contact at the slip rings, and the brush..."
joe_jochoa posted an answer for this Miller Trailblazer 302 AC/DC Welder Generator - Kohler Gasoline Engine with GFCI:
"there are a few things you can check on your machine, make sure your machine is not in the..."
joe_jochoa posted an answer for this Lincoln Welding Tools:
"weld current and idle control on this machine is controlled by the main circuit board, you..."
joe_jochoa posted an answer for this Lincoln Electric K1297 AC/DC 225/125 Stick Welder:
"weld current output regulation on this machine is usually accomplished by voltage supplied..."
joe_jochoa posted an answer for this Welding Tools:
"check the leads and connectors at the idle control solenoid, make sure they are making..."
joe_jochoa posted an answer for this Lincoln Electric Welding Tools:
"not knowing what model you have makes it almost impossible to suggest a repair, however,..."
joe_jochoa posted an answer for this Lincoln Electric Welding Tools:
"as with any gasoline engine, you need, fuel, spark & air, take a moment to follow the..."
joe_jochoa posted an answer for this Kipor Generator Kge2400 - 2400 Watts:
"You are discussing a bridge rectifier, the + connector is directly opposite the negative..."
joe_jochoa posted an answer for this Welding Tools:
"remove the side doors, and top cover, make sure your brushes are making correct contact..."
joe_jochoa posted an answer for this Electrical Supplies:
"locate the three diesel fuel lines that ate connected to the fuel injection pump, loosen..."
joe_jochoa posted an answer for this Miller Trailblazer 275 DC Welder Generator - Kohler Gasoline Engine:
"there is a voltage regulator directly above the electric fuel pump on this welder, make..."
joe_jochoa posted an answer for this BlueStar Miller Bluestar 185 Dx Gas Weldergenerator 907269:
"Check your idle control module, take the roof off of your welder, located at the top..."
joe_jochoa posted an answer for this Kohler CH25 PA-CH730-0040 Command Gasoline Engine:
"with the engine running, connect a dvm across the battery, in high idle, your meter should..."
joe_jochoa posted an answer for this Lincoln Electrical Supplies:
"The Lincoln Classic 3D welder has a flashing diode attached between the main generator..."
joe_jochoa posted an answer for this Welding Tools:
"welding gas regulators and torches and valves can be sent to: Matheson Tri gas 251 Scott..."
joe_jochoa posted an answer for this Lincoln Electric Classic 300D Welder/Generator with Engine Option Engine Type: Perkins, Wire Feed Module for Perkins Engine: Yes, Wire Feed Module for Kubota Engine: No:
"Yes, You will have dis mantle the front of the machine, The front control panel will have..."
joe_jochoa posted a question about HP Pavilion dv6000z Notebook:
"computer turns on, all the blue lights operate, there are no keys that are stuck, I have..."