Toro Garden - Page 5 - Recent Questions, Troubleshooting & Support
What length is a deck belt on a toro lx460
1/2" x 90" ; Toro P/N 112-5834
Try:
http://www.tractorsupply.com/outdoor-power-equipment/mowers-attachments-accessories-parts/mower-parts/mower-belts/huskee-v-belt-1-2-x-90-in-4461290
for $19.49 if you have a Tractor Supply Company nearby.
Or:
http://www.texasmowerparts.com/catalog/products.asp?ds=DETAILED&category_id=47&group_id=184§ion_id=585
# Replaces Toro 112-5834 # 1/2" X 90"
for $14.17 + $5.95 shipping
Danotex
Can't get to the coil in a 38-1-20 Toro snowblower how do I
That's an older Tecumseh engine. The magneto and points are underneath the flywheel.
See Taryl Dactyl instruction video on how to remove a flywheel without a puller and 100s of small engine repair videos.
https://youtu.be/SYVjw7fw8RU
Youll need specs for point gap and timing instructions. See free manuals at
https://www.mymowerparts.com/pdf/
Parts diagrams.
https://www.ereplacementparts.com/toro-38120-000000100150001980-snowthrower-parts-c-121776_121777_122189.html
2/6/2021 3:09:43 AM •
Toro Garden
•
Answered
on Feb 06, 2021
How to remove a front wheel from a Toro Wheel Horse 520H garden tractor,(maybe about a '98 model year?)
Review diagram at;
https://www.partstree.com/models/41-20oe01-520-h-toro-garden-tractor-1990/wheels-and-tires-35/
Raise and secure front of mower off the ground.
Remove large wheel cover (if in place).
Remove small dust cap.
Remove cotter pin.
Remove castle nut.
Remove flat washer.
The wheel should now be loose and the outer roller bearing can be removed. Next slip the wheel off the spindle. Take care not to loose any parts from backside of the wheel.
9/20/2020 1:54:09 PM •
Toro Garden
•
Answered
on Sep 20, 2020
My Toro Timecutter MX5060 74641 makes a clicking noise when attempting to start as if the battery doesn't have enough charge.
Likely the starter solenoid or the brake actuator module.
You'll need to measure the voltage at the starter solenoid coil. You should read battery voltage across the solenoid coil when the ignition switch is in the start position.If you don't read battery voltage, there are multiple causes for this fault.
For engine START, this unit requires the following;
PTO switch OFF
Steering arms OUT (brakes fully applied)
Operator seat occupied.
When steering arms move OUT the brake actuator module applies brakes and allows the power to the starter solenoid coil when the ignition key is rotated to the START position given the 3 conditions above are met.
The brake actuator must rotate and apply the brakes or the unit will not start. Any obstruction of the brake linkage that prevents full brakes or if the actuator is out of adjustment will prevent starting.
9/16/2020 8:10:35 PM •
Toro Garden
•
Answered
on Sep 16, 2020
I have a Toro Ultra Blower Vac model 51609. I've had it for several years. For some unknown reason, the impeller has started spinning in the opposite direction.
It is well known a single phase induction motor can change direction but that type of motor is too heavy for portable equipment and a series -wound brush type motor is commonly used due to their much lighter weight.
I can think of no fault that would cause your motor to run backwards though I suppose it might be possible to fiddle with the internal connections...
One thought does occur however - as it is a variable speed tool. The speed control could be a type that outputs DC or direct current instead of alternating current and in that case if it suffered a fault that could conceivably reverse the polarity, it would reverse the motor direction.
4/25/2020 11:23:02 PM •
Toro Garden
•
Answered
on Apr 25, 2020
Not finding what you are looking for?