Kenmore Elite - Recent Questions, Troubleshooting & Support - Page 5

0helpful
1answer

Kenmore Elite HE4t Washer won't start

Hello Ameliafaith, E-Z job... If you take your model on line... to SEARS (I don't ordinarily recommend)... BECAUSE THEY COULD ACTUALLY ... decode your ABREVIATED part number... 110. blah blah blah... (45986??) The other sites actually have helpful VIDEOS... But I already wasted enough time on this floundering with your erroneous number (wrong no.)... You will see these parts are reasonably priced and very popular.. meaning they INDEED FAIL ... alot. Go here: Washer Door Lock Assembly Part Number 8181700 Sears PartsDirect Carnac the Magnificent
6/7/2017 3:12:50 AM • Kenmore Elite... • Answered on Jun 07, 2017
0answers
0answers
0answers
0helpful
1answer

HE5t Steam shows SUD then f35

SUD means there are too many soap suds in the washer. Are you using a front load approved detergent? Are you using the correct amount? or slightly less is better.
5/12/2017 10:39:11 PM • Kenmore Elite... • Answered on May 12, 2017
0answers
0helpful
1answer

Broken shock absorbers on front loading Kenmore

Hi, first things first. Your model and serial numbers should be on a sticker somewhere around the door opening. Next check the tub. With your finger,push up on the rim of the tub then rotate the tub a few inches and push up again. Continue through a whole rotation. If the tub moves and make a clicking noise you have a bad drum bearing and the cost to repair is more than the unit is worth. If that's not an issue,then it's probably just the shocks,replacing them should solve the problem. Hope that helps.
5/8/2017 12:15:31 PM • Kenmore Elite... • Answered on May 08, 2017
0helpful
1answer

Front load Kenmore HE3t washer wont start

If I remember correctly you have to move the door boot seal out of the way by removing the wire ring underneath to get inside to the door switch there are two screws holding in the latch on the outside
5/4/2017 1:25:11 AM • Kenmore Elite... • Answered on May 04, 2017
0helpful
2answers

Error F51 for Kenmore Elite Oasis Toploading

bad main board or motor possitioner sensor.. most likely motor sensor.
China made junk parts with a million problems
5/2/2017 11:46:18 PM • Kenmore Elite... • Answered on May 02, 2017
0helpful
2answers

In mid wash the Kenmore Elite Oasis HE flashes F51 and

check if basket turns freely. if it does replace the main board
5/2/2017 11:42:19 PM • Kenmore Elite... • Answered on May 02, 2017
0helpful
1answer

Kenmore Elite HE3t which F21 code

I'm guessing the HOSE is the drain hose. The goop is causing the drain motor to overheat causing it to report error. (luckily or it'd burn out). Give it a empty load with nothing in it to see if it flushes it all out. Just water. See if it completes full cycle and check pump filter again to see if clean. TIP. Make sure you check ALL pockets before you wash clothes. ;)
4/17/2017 2:53:34 AM • Kenmore Elite... • Answered on Apr 17, 2017
Not finding what you are looking for?
Washing Machines Logo

5,309 questions posted

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Alexander

Level 2 Expert

171 Answers

Cindy Wells

Level 3 Expert

6688 Answers

vince

Level 3 Expert

2530 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kenmore Washing Machines

  • Forum

View Most Popular

  • Kenmore Washing Machines
Loading...