Haier Washing Machines - Recent Questions, Troubleshooting & Support

try unplug the washer an waiting 5 min it should unlock if , if ti does onlock you made need call a appliance servce tech

English only on this North American Fixya please. Vince XQB22-19 washing machine user manual. It does not work. https://www.google.com/search?q=%E2%80%8BVince+XQB22-19+washing+machine+user+manual ..

Question edited for clarity. Question moved from Firearm Optics category. It looks like you solved it yourself as to what is means https://www.manualslib.com/manual/1197834/Haier-Hw80-B14266a-Ec.html?page=21 More here, but no one gives the reason. https://www.google.com/search?q=haier+HW80+washing+machine+error+code+Fb Model number appears to be incorrect as 'PD1626'? https://www.google.com/search?q=HW80+PD1626 ..

First, confirm that the dishwasher display is working. If the display is still working, try pressing some of the touchpad buttons. If some of the buttons respond correctly but others don't, it is likely that the touchpad is at fault. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)

Question edited for clarity. My guess is that your drain hose is too high. The pump is in the base of the washer and pushes the water up the tube and into the drain/ when the pump stops, the residual water in the hose drops back into the base of the machine, so the higher the hose, the greater the column of water. https://www.manualslib.com/manual/837407/Haier-Hlp21n.html?page=10#manual Or The Drain Pump is blocked or failing. ..

Are You Looking For a Best Mobile. <a href="https://watmobile.com/">Whatmobile</a> Will Help You To Find mobiles with all specification. Latest Mobile Prices in Pakistan.

this could possibly help.... https://www.youtube.com/watch?v=D2jYHVzu0Sg

Door not closing properly. Hinges may need adjusting. The door switches are very sensitive

The first thing to do is to clean the machine following the manufacturer's directions in the owner's manual. I've seen a number of washing machines that generated fault codes because lint or other muck gummed up a sensor; the cleaning process often is enough to take care of the problem. In the U. S., we have a product called CLR (Calcium, Lime and Rust remover) that does a nice job of cleaning out washing machines. I think the primary ingredient is dilute citric acid. Some manufacturers recommend chlorine bleach - go with what is in the manual first. If the cleaning process doesn't eliminate the error code, yes, you probably still can fix the washer, if you can open it. If you know the model number, you may even be able to obtain a service manual that will tell you what to look for. Warning: unplug the machine before removing any covers. Exposed electrical terminals are a shock hazard if the machine is plugged in. Some appliances have a wiring diagram attached inside, or on a service sheet stored inside the control panel. If you find it, the wires going to the temperature sensor will be identified by the colors. For example, a YEL/BLK wire is yellow with a black stripe. You can trace these wires to find and identify the temperature sensor. Once you find the sensor (it will be somewhere in contact with the wash water, probably on or near the tub), inspect the electrical connections at the sensor and at the control unit, and clean up or repair any corroded connections. Check the wiring to make sure it hasn't been pinched between parts and damaged. If the wiring looks good, take the sensor out and remove any muck that is built up on it. Be sure to wipe clean the gasket or o-ring, and any sealing surfaces in contact with the gasket. Re-install, put the machine back together (being careful not to pinch any wires between parts or panels!) and test it. If you still get the error, you may have to replace either the sensor or the controller.

Take the 4 screws out of the top section, lift up the whole top. You will see a bar. You must lift the top so the bar raises above the drum. Take the screws out of the plastic cover and check the bar .it has 2 round ends that rest in two holes. If it came out of one simply place it back in the hole. You will hear it click when pressing it. Put back together. Problem solved.

Hi, Try a power cycle before replacing any parts. You can also turn your dial counter clockwise and retest the wash. Otherwise, I would suggest setting up an appointment with home depot to get a full list of parts that need to be replaced in your washer. Thank you.

Did you ever figure out the problem? Mine does the same thing. Just immediately drains and then nothing happens.

check drive belt if ok possible cogs under agitator need to be replaced

SUSPECT THE CONTROL BOARD DIED BUT ONLY A SERVICE TECH CAN TELL YOU FOR SURE AND THEY ARE NOT CHEAP

If resetting the washer doesn’t work, the limit switch may be stuck. The sensor for a unbalanced load is a limit switch. The switch should snap back into standby position when the wash tub comes to a stop. Sometimes the switch will stay stuck. Move the barrel by hand back and forth until it hits the inner walls of washer. It may knock the switch back in place.