Chevrolet Heating & Cooling - Recent Questions, Troubleshooting & Support

SDM airbag tech info - GM Air Bag, Black Box, EDR, Event ...

www.airbagcrash.com/sdmairbagtechinfo.html

GM air bag black box / EDR / event data recorder / SDM / deployment crash data ...Buick, Cadillac, Chevrolet, Pontiac, Oldsmobile, GMC, Hummer and Saturn ... control module, pcm, event data recorder. edr, truck, airbag testing, air bag ... EDR 'black box' air bag module location list posted below. ..... Suzuki 2007-2014

Chevrolet Tahoe location air bag module Questions ... - Fixya

www.fixya.com > ... > Cars & Trucks > Chevrolet

Ask your Chevrolet location air bag module related question. Get free ... How do I fix my ABS control Module for 2001 Tahoe ... How to reset airbags in a 2007 tahoe ... Where is the Air Bag computer modual located for the 2005 Tahoe Z71?Missing: hevrolet ‎avalanche

BCM Basics 101 (03-06) - Chevy Avalanche Fan Club of North America

chevyavalanchefanclub.com > ... > CAFCNA's Sperry Tech Center

Aug 8, 2015 - 3 posts - ‎2 authors The Body Control Module (BCM) performs multiple body control functions. The BCM can control devices directly connected to its outputs based ...Missing: hevrolet ‎bag

Sounds to me like faulty distribution box unit that supplies the power to the battery.I suppose you checked the fuses?

if bent and hanging /disconnected someone had and accident order the replacement parts and replace tan either an alignment shop to check that repair is safe and an alignment can be done but preferred method or repair would be a body shop for repair

ABS uses only brake lines. The power brake booster uses 1 vacuum line. Did you mean PCV lines?

You have air in the power steering lines. Was the fluid low or do you have a leak? Car off, in park, raise your front end, both front wheels off the ground with a floor jack. Start the engine and turn the wheel all the way right and left a couple times. Add more PS fluid if necessary and do it again. Air compresses but the fluid does not. Turning left uses almost all the fluid to push the arm out of the piston. Moving it all the way right will allow the air to escape in the fluid reservoir.

The computer in the car is telling you that a trouble code has been set in the computer and it is going into limp home mode. You need to put a scanner on the car and see what the code is and have it repaired. Hope this helps.

Sounds like when the problem happens the truck goes into limp home mode in the computer, which would not allow the truck to go over about 30 mph, So when the problem happens you need to put a scanner on the obd link and read the code which will tell what part of the abs system is giving you problems. Hope this helps.

Did you align the rotor in the dist. to #1 cylinder in the firing order if not you will not get fire to spark plugs. Is the unit backfiring when you turn it over or does it just roll over. Let me know.

I'm afraid an 04 malibu doesn't have a fuel shut off switch, sorry.

Have a proper diagnosis done by a professional who knows what he is doing. Guessing at problems and changing parts is not a sensible means to proceed. It may well be that the internals of the transmission are badly worn and you will need a rebuilt unit installed. Just changing bits and pieces of electronic equipment and hope that works is not a solution.

Hi Mike: Four possibles? 1) Oil pump problem 2) Oil pressure sensor/sender problem 3) Oil pressure guage problem. 4) Bad wire connection between sensor and guage Being really "Old School" I'd see if it is possible to install a "real" oil pressure guage so that I knew what was happening. - If you don't have oil pressure within 10 seconds of the engine starting I would be concerned. - How many km on the engine? - maintenance history? - problem history? - Are you the original owner? Reply as a COMMENT to this post and I'll try to help. Cheers.

Sounds like the sending unit in the tank is either worn out or losing contact once in a while. You will need to change the unit out. Before you do that check the grounds and make sure they are tight.

Did you have a front end alignment done? If the tie rods were changed then that could be out. Bad wheel bearing?

Tell the parts store the make, model, year and what part you want to replace and he/she will look the part up on there system and give it to you. Once you replace the brake cylinder you will need to bleed the brakes and get the air out of the lines and cylinders. Hope this helps.

The neutral switch is on the steering column near the floor on the interior of the car. It is half moon shaped and screws to the steering column. Do not move anything such as the gear selector when replacing the switch. Replace it and once it is tighten down then put it in park. Hope this helps you.

No sure but when I had the problem the dealer told me they need to drive the car for about 50 miles to allow the computer to cycle through all the programs. Hope this helps.