Food Mixers - Recent Questions, Troubleshooting & Support

This is so weird. I have the exact same serial number for my Camfield mixer with the same model (I'm guessing from about 1955-57). I wonder if they just put the same serial number on for products created at the same time. I thought 6404 was really low. Did you ever find replacement beaters? Mine have rusted. This was my mother's mixer and I just have a fond place in my heart for it.

I need service manual for kenwood KMM770

It uses a food approved oil.

Question moved from Cars and Trucks. Stand Mixers don't normally have belts and I don't believe this one does as I can't find spare belts. They are operated by nylon cogs that run in grease. The most likely reason is the she shear pin has sheared. This is a small pin like a nail that goes through a cog or shaft and shears if too much load is put on the mixer beater or dough hook. It often happens if you make bread and have the speed too high. https://www.google.com/search?q=change+the+belt+in+a+Bodum+electric+mixer ..

Here is the Technical Manual https://www.partstown.com/modelManual/HOB-A200_spm.pdf Repair help and videos. https://www.google.com/search?q=hobart+a200+repair

Hobart A200 Restoration

The Fresh Loaf https://www.thefreshloaf.com > node > a200-restoration Mar 8, 2020 - I'm currently disassembling my A200 and I can't seem to get the planetary to just slide off like the videos seem to show. Am I missing something ...

My Hobart A200 rebuild

The Fresh Loaf https://www.thefreshloaf.com > node > my-hobart-a200-... Oct 21, 2021 - So I took it completely apart, cleaned and degreased it inside and out, stripped the old paint, replaced the worn parts (power cable, bearings ... ..

You will need to get a qualified electronics technician to look at it. The issue could be anywhere on the circuit boards inside the mixer. Unless you know what you are doing don't try to repair it yourself as you could make the problem worse.

This is a commercial mixer and they are horrible to work on. Heavy and covered in thick grease. Probably lost a screw or sheared a shear pin. Call your catering equipment service guy.

Hi I am try to find cake wicker model qf3473

i have a spare unit for dsale 1500.00 cdn

It is a Start Capacitor. It give the motor a jolt to get it running.

HOBART, Fits Hobart Brand, For A120/A200, Capacitor ...

Grainger https://www.grainger.com > product > HOBART-Capa... HOBART Capacitor, Motor Start: Fits Hobart Brand, For A120/A200 ; Item: 235F28 ; Mfr. Model: 00-070487-00025 ; Catalog Page: N/A. US$41.13

MOTOR STARTING CAPACITOR FOR HOBAR MIXER ...

eBay https://www.ebay.ca > ... > Commercial Mixers MOTOR STARTING CAPACITOR FOR HOBAR MIXER MODEL A200 REPLACES 7048700018 ; Condition. New ; Quantity. 67 sold. 82 available ; Item Number. 254321066847 ; Brand. Rating: 5 · ‎ 1 vote

Motor Starting Capacitor Fitting Hobart Mixers A120, A200 ...

National Band Saw Parts https://nbsparts.com > All Products MOTOR STARTING CAPACITOR FOR HOBAR MIXER MODEL A200 REPLACES 00-070487-00018. 125V, 50/60HZ, 145-174uF. Includes: One Capacitor. Replaces#: 00-070487-00018 ... US$30.00 · ‎ In stock https://www.google.com/search?q=Hobart+A200+the+capacitor+is+starting+or+running+capacitor ..

Spray some WD40 into the eject button. The wait 10 minutes and turn it upside down and spray WD40 down the side of the beaters Leave 10 minutes and try again/ If that doesn't work, you will need full disassembly ..

Hi Carol , I had the same problem. You should open the main cover, then, remove the 3 screws (see picture), and remove the nickel plated ring, then, take out one screw from the bottom (see picture), then open 4 screws that holds the gear box from the top . good luck. Pini

Please state whether user or maintainance manual.

The trim ring news to be ta]ed in place with a plastic-face mallet. This type of mallet does not (if used properly) Mar the surface it striks. Hold the trim ring in place while tapping it in place. It often takes patience to get it right. The ring is properly in place when there is no place where you can insert a fingernail between it and the mixer body all around the ring.

Usually plastic latching clips that you ease out with a tool called a Spudger. It look a bit like a short bladed butter knife. https://www.google.com/search?q=oster+2534+hand+held+mixer+disassembly The video may not be the same as yours, but the construction will be similar. ..

The bevel gear sits above the worm-follower gear. I think you mean the drive attachment gear.I think I have the same, or similar problem. I ground a piece of meat that stopped it from working. The drive-attachment-gear turns if I push it in, but then it pops out. I am still trying to figure out what part is causing the issue - the drive attachment gear, or maybe even the worm follower gear.

Cuisinart hand mixers are not repairable. You can buy replacement accessories like beaters, but you can't buy any internal replacement parts.

I have a Cuisinart HM-70 and I stripped the plastic gears inside by trying to mix a really thick dough. It was easy to open and get to the plastic gears. When I called Cuisinart to try to get replacement gears, they said that they don't sell replacement parts and their hand mixers are not repairable. I looked all over the internet and no one sells internal parts.

Unless your mixer is still under warranty, I believe that you're out of luck and your mixer is headed to the electronics recycle pile.

Most handmixers today are sold with plastic gears - including high end brands like Viking. For me the lesson learned is to buy low end hand mixers (don't buy a top of the line 9 speed mixer) and treat them like they're disposable when they break.

Question edited for clarity. The drive train probably need cleaning and re-greasing, but there is also a gear that wears out. https://www.google.com/search?q=Kitchen+Aid+Mixer.+How+to+fix+a+grinding+sound+when+switch+is+on+Medium+speed ..