Electrical Supplies - Page 4 - Recent Questions, Troubleshooting & Support
Can this controller be replaced with a controller thats not nema 4
Whether or not a NEMA 4 controller can be replaced with a controller that is not NEMA 4 depends on the specific application. NEMA 4 controllers are designed to withstand water and dust ingress, so they are often used in outdoor or harsh environments. If the controller is being used in an environment where it is exposed to water or dust, then it is important to replace it with a NEMA 4 controller.
Overall, it is important to consult with a qualified electrician before replacing a NEMA 4 controller with a controller that is not NEMA 4. The electrician can assess the specific application and recommend the best controller for the job.
If you want to look for a controller, you can visit: https://www.chipsmall.com/bigcategory/industrial-automation-and-controls.html to search for the controller you want.
What is the colored wire positions on a craftsman 2400 mower key switch
See following URL for complete wiring diagram.https://www.searspartsdirect.com/model/3x23oa7iyt-000247/craftsman-917203831-front-engine-lawn-tractor-partsSwitch Terminal to circuit color.B RedS WhiteM Black (Black/white)A1 BlueA2 BlackL BlackG BlackUnfortunately 4 of the circuits are not uniquely color coded. If the black wires have been disconnected from the switch socket then it will be necessary to identify each black wire to its respective circuit.
10/13/2023 5:49:31 AM •
Craftsman...
•
Answered
on Oct 13, 2023
I have a generac ix
You engine has a low oil level sensor. If the oil level is low or..... the sensor is bad it will ground the ignition from the coil with the engine switch on. For troubleshooing only disconnect ONE wire from the sensor AFTER you make sure the engine oil level is properly serviced. Then check for spark.
If this does not correct the problem just respond and I will help you.
Thanks for choosing FixYa,
Kelly
I need a replacement thermostat for my Robertshaw 9420, will a Robertshaw 9560 be a close replacement?
Replacing a thermostat with a different model requires careful consideration of compatibility, wiring, and features. To determine if a Robertshaw 9560 can replace a 9420:
- Verify compatibility with your HVAC system based on manuals.
- Check wiring compatibility or consult an HVAC technician.
- Compare features to meet your heating/cooling needs.
- Ensure programming aligns with your requirements.
- Confirm power requirements match your setup.
- Assess the user-friendly interface.
- Check thermostat size and mounting options.
- Prefer professional installation if unsure.
- Investigate warranty and support for the 9560.
I have a Yamaha Ef2600 fw generator that starts and produces voltage and current but also gives out a 'clunking' noise on a 2 - 4 second cycle. What is wrong with it?
Based on the search results there are a explanations, for the clunking noise in your Yamaha EF2600FW generator;
1. Load handling; One potential reason could be that the generator is facing difficulties in managing the load, which could be due to fuel or air supply. This can result in the generator producing a clunking noise.
2. Fuel shortage; Another possible cause might be a lack of fuel supply to the generator leading to a knocking sound. It is advisable to address this fuel issue before operating the generator to prevent any damage.
3. Storage conditions; The clunking noise could also arise from storage conditions. Over time certain components like piston slap or dry rod bearings may develop problems resulting in sounds when the generator is running.
To diagnose and resolve the problem with your generator it is recommended that you take the steps;
Check and ensure a fuel supply. If needed, clean or replace the carburetor.
Inspect the generator thoroughly for any signs of damage or wear in areas like piston and rod bearings.
These actions should help. Rectify any issues causing the clunking noise, in your Yamaha EF2600FW generator.
If the problem continues you might need to reach out to a technician or get in touch, with Yamaha customer support for help. Always prioritize safety when dealing with generators or any other equipment. If you feel uncertain or uncomfortable about troubleshooting or making repairs yourself it's best to seek assistance, from a professional.
8/25/2023 9:54:21 PM •
Yamaha...
•
Answered
on Aug 25, 2023
Not finding what you are looking for?