AEG Washing Machines - Page 8 - Answered Questions & Fixed Issues
My AEG OKO LAVAMAT 13.50year 2005 turns off after a few minutes washing
check your power cord for continuity (ohms). If your power cord checks good, I would look at either the noise filter board or the user interface board or main control board. Start with checking your outlet. make sure it is wired correctly with proper voltage and grounding. You can buy an outlet tester at Lowe's or Home Depot. Really cheap. Has lights on it that tells you if wiring, grounding and voltage are right. if that checks good, proceed to machine. If I can help further, look for me on 6ya
11/27/2015 9:59:21 PM •
AEG Washing...
•
Answered
on Nov 27, 2015
•
81 views
Aeg oko lawamat
c9 means the motor is not turning the drum. check carbon brushes in the motor.
10/30/2015 8:15:27 AM •
AEG Lavamat...
•
Answered
on Oct 30, 2015
•
1,069 views
AEG Lavamat 60810 E70 7Beeps Does seem to still work but display shows E50 and some time E70 and 7beeps over and over. Many thanks
First of all, read exactly alarm code.
Press "Spin/Rinse hold" button and "Prewash" simultaneously for at least 2 seconds: the LED switch off and then display the
sequence of flashes indicating the alarm.
The alarm sequence is displayed for the time in which the buttons are hold down. During the time the alarm is displayed, the appliance continues to perform the cycle or, if it is in the
selection phase, it keeps in memory the options previously chosen.
E70 - Family alarm code
- E71 - Washing NTC sensor faulty
- E74 - Washing NTC sensor badly positioned
Causes: NTC sensor badly positioned; NTC sensor faulty; wiring faulty; PCB faulty.
E50 - Family alarm code
- E51 - Motor power supply triac short-circuited
- E52 - No signal from motor tachometric generator
- E53 - Motor triac sensing circuit faulty
- E54 - Motor relay contacts sticking
Causes: Motor faulty; wiring faulty; PCB faulty; current leakage from motor or from wiring
Dado
10/12/2015 10:28:18 PM •
AEG Washing...
•
Answered
on Oct 12, 2015
•
504 views
AEG Lavamat washing machine model 76850, shows a blinking key and makes clicks and after that shows E40. Thanks John
Family error code E40 is visible to customers and (could be E41,E42,E43,E44 and E45 only visible in service mode) means problem with open door or door interlock.
I suggest rapid reading alarm code when appliance is in normal operating mode (e.g. during the execution of the washing
programme):
Press and hold down START/PAUSE and any of the option buttons for at least two seconds: the LEDs initially switch off, and then display the flashing sequence corresponding to the alarm.
The alarm sequence continues as long as the two buttons are held down.
E41 - Door open
E42 - Problems of door closure
E43 - Interlock power supply triac faulty
E44 - Door interlock sensing circuit faulty
E45 - Door interlock sensing circuit triac faulty
Possible causes:
Door interlock faulty, wiring faulty or PCB faulty.
Dado
9/6/2015 7:33:07 AM •
AEG Washing...
•
Answered
on Sep 06, 2015
•
1,542 views
Aeg 72630 update
Press first left up button and first left down button simultaneously
( during the execution of the washing programme ) for at least 2 seconds: the LED switch off and then display the sequence of flashes indicating the alarm.
The alarm sequence is displayed for the time in which the buttons are hold down.
When you read the alarm code,we will be able assume what may be faulty.
Dado
8/21/2015 7:45:21 PM •
AEG Washing...
•
Answered
on Aug 21, 2015
•
152 views
How do I reconnect hose?
1. Bend or put on back side the appliance and remove the three screws which secure the plinth to the lower part.
2. Remove the filter door
3. Remove two screws
4. Release the plinth
5. Turn it
6. Remove the plinth
Dado
Oko 72630. Why is it stuck on rinse cycle?
Could be several reasons:
- Selected the "Night cycle" program (means standing with the drum full of water, reason: too much noise in the spin cycle)
- Set to the "Rinse hold" (means standing with the drum full of water, reason: wrinkles on the clothes)
According to your description I think that this is not a failure otherwise error E20 will be appears on display.
Once the washing programme has come to an end, END illuminates on the programme progress display.
If RINSE HOLD was selected, the display beside the START/ PAUSE button flashes.
1. After a rinse hold, the water must first be pumped out:
- Either press the START/PAUSE button (the water is pumped out and the washing is spun according to the completed programme;
After the START/PAUSE button is pressed again, the spin speed can still also be changed during spinning), or
- Turn the programme selector to PUMP OUT and press the START/PAUSE button (the water is pumped out without spinning),or
- Turn the programme selector to SPIN or SHORT SPIN and press theSTART/PAUSE button (the water is pumped out and the washing is spun or gently spun).
At the end of this programme step, the END indicator will illuminate.
2. Open the door.
As soon as the DOOR indicator lights up green, the door can be opened.
Dado
8/18/2015 7:14:22 PM •
AEG Washing...
•
Answered
on Aug 18, 2015
•
1,675 views
How do i reset washing machine AEG 64840
You can choose the right programme for any type of laundry following the descriptions on the washing programme tables (see «Washing Programmes»).
Turn the programme selector dial to the required programme. The programme selector determines the type of washing cycle (e.g. water level, drum movement, number of rinses) and the washing temperature according to the type of laundry.
The pilot light of button 8 starts blinking.
The selector dial can be turned either clockwise or anticlockwise. Position "0" to Reset programme/ Switching OFF of the machine.
At the end of the programme the selector dial must be turned to position "0", to switch the machine off.
If you turn the programme selector dial to another programme when the machine is working, the yellow pilot light of button 8 will blink 3 times and the message Err is displayed on the display to indicate a wrong selection. The machine will not perform the new selected programme.
Dado
7/18/2015 5:18:03 PM •
AEG Washing...
•
Answered
on Jul 18, 2015
•
2,145 views
What is the reset code
Obviously, in the washing machine is residual water. Pressure switch has not switched from a "FULL" state to a "EMPTY" state and because that drain pump works continuously.
Check the hydraulic circuit of pressure switch and the correctness of the pressure switch. Also check drain pump and its hydraulic circuits.
Dado
7/5/2015 10:05:17 AM •
AEG Lavamat...
•
Answered
on Jul 05, 2015
•
152 views
Error c3
http://www.aeg.co.uk/Support/Troubleshooter/?Command=Detail&CatId=98&SymptomId=1412&DetailId=1412shows AEG's meaning for a C3 error code
6/14/2015 5:19:25 AM •
AEG Washing...
•
Answered
on Jun 14, 2015
•
855 views
How do I remove the Transit Bolts?
Hi,I dont know about AEG but on some of the washing machines that I have done,I found that they are located on the back of the machine,and they just unscrew anti clockwise,and you should have some plastic blanks that go in the holes.
I hope this was some help,all the best.
6/11/2015 10:24:03 PM •
AEG Washing...
•
Answered
on Jun 11, 2015
•
181 views
Not finding what you are looking for?