AEG Washing Machines - Page 7 - Answered Questions & Fixed Issues
Error code e9 on hob aeg hk85440075
From another Post from Daniel T:
E9 on this hob means a user interface control board fault. This is the touch control board which you press to turn on.
What the service manual says is disconnect the hob from the mains connection and leave for 60 seconds. Then wire it back up and turn back on and see what happens.
If still the same then the user control board needs to be replaced.
To access this you need to remove the hob from the work top and remove the screws holding the glass on all 4 sides of the hob.
Then you can lift the glass top off.
From there you will see the user board in the front its the smaller board.
Replace this and that should cure the fault here.
If you need anymore info just get back to me.
My Zanussi induction hob flashes an error code E9 when try
6/17/2016 5:49:31 PM •
AEG Washing...
•
Answered
on Jun 17, 2016
•
3,594 views
What does it mean code EHO on a frontloader aeg brand
This causes a water leakage, which flows inside the bottom of appliance, thus switching on the Aqua Control sensor and generating alarm EF0/EF3.
Be sure to find water leaks and repair the defect.
Incline the washing machine of about 10 cm to spill the water, so that the sensor can operate normally again.
Dado
5/22/2016 7:34:44 PM •
AEG Washing...
•
Answered
on May 22, 2016
•
294 views
Water overfills. change pressure
sensor. I have a AEG Lavamat
1000 front loader Washing machine
In many situations the cause of failure is mechanical and not electrical. Pressure sensor usually has three terminals: GND, + 5DC and AC signal, because that always should first check the power supply and then the AC signal, which is usually 44 kHz and means empty tub, 40 kHz means approximately 160mm water in tub, while 36 kHz means approximately 300mm water in tub. So, if there is a power supply voltage +5 DC and AC signal to the PCB, most likely hydraulic system of pressure sensor does not seal well or is clogged, so the PCB does not receive information on the amount of water in the tub even though the pressure sensor is correct.
Dado
7/25/2016 7:04:47 PM •
AEG Washing...
•
Answered
on Jul 25, 2016
•
361 views
AEG L87480 on desplay makers E91 what means
E90 is family error code visible to the customers. It is necessary to read the error in the service mode so please proceed with the following procedure for rapid reading of alarm codes:
Press and hold down START/PAUSE and the option button nearest to the START/PAUSE button for at least two seconds!
After that the display will show one of the following errors that are more precise:
E91, E92 - Communication incongruence between main board and display board (versions not compatible). Posible causes: wirings, main board or control/disply board.
E93 - Incorrect configuration of appliance. Posible causes: Incorrect configuration data; electronic board faulty.
E94 - Incorrect configuration of washing cycle.
Posible causes: Incorrect configuration data; electronic board faulty.
E95 - Communication error between microprocessor and
EEPROM. Posible causes: Electronic board faulty.
E97 - Incongruence between programme selector and
cycle configuration. Posible causes: Faulty electronic board (Wrong configuration data).
Considering that this is a complicated fault, my advice is to contact an authorized service center.They have special equipment such as an interface that allows them to upgrade software in your appliance. If you are not doing anything on the appliance before the failure, the only thing you can check is the contacts between wiring and electronics.
Dado
4/24/2016 6:45:29 PM •
AEG Washing...
•
Answered
on Apr 24, 2016
•
1,437 views
My AEG OKO LAVAMAT 72640 keeps stopping mid cycle and flashing error cod E10 what can I do?
The water Supply
1. First, check that the tap is not accidentally turned off.
2. Check that the gray water inlet hose is not squashed or kinked lies.
3. It is also possible that the filter is clogged in the supply hose. Close the tap and disconnect the hose. Here is some pressure on it, so keep a towel handy. Check the filter that output waterklraan, and clean it if necessary.
4/16/2016 5:59:18 PM •
AEG Washing...
•
Answered
on Apr 16, 2016
•
609 views
Remove housing
? 5:38
https://www.youtube.com/watch?v=KlAXmnKJQ9k
Aug 17, 2009 - Uploaded by eSpares
This video will show you how to remove and replace the door seal. ... Do you have video repair instructions for AEG washing machine OkO ...
AEG removing drum Washing Machines Questions ... - Fixya
www.fixya.com/tags/
removing_drum/
washing_
machines/
aeg
AEG washing machines removing drum related questions and answers. ... into thehousing and get the object out. well as we say in my town you got a "toston" .
Aeg/electrolux lavamat 76810 waschmaschine E20 - YouTube? 0:28https://www.youtube.com/watch?v=1WX5rKxFrXsMay 3, 2015 - Uploaded by jusuf jerkovicAeg/electrolux lavamat 76810 waschmaschine E20 ... front load washer from not draining -- washing machine error code e20 - Duration: 2:52.washing machine error code e20 - YouTube? 2:52https://www.youtube.com/watch?v=2B7FxovrxKoOct 25, 2014 - Uploaded by teppichkopfSave some money and fix it yourself. Totally bizarre how stuff gets stuck in the drain!
12/21/2015 7:07:11 PM •
AEG Washing...
•
Answered
on Dec 21, 2015
•
441 views
Power is on but not working
Firstly ......are you saying NO POWER? no lights or display? If not then unplug check mains fuse. If fuse OK. then do test wash. empty out see whether any different. If not then valve inlets? Or Pump if not draining out. DONT TINKER IF NOT CONFIDENT. Electricity kills. BE SAFE.
12/14/2015 1:08:45 PM •
AEG Washing...
•
Answered
on Dec 14, 2015
•
77 views
Not finding what you are looking for?