AEG Washing Machines - Page 6 - Answered Questions & Fixed Issues

Lavamat 110 doesn't exist. Maybe it's a lavamat 1100;1105 or similiar... Dado

Following next link: How washing machine door lock works how to test interlocks Replace door lock. When the washing programme is started by pressing the START/PAUSE button, the bi-metal PTC (contacts 3-5) is powered by the triac on the PCB (J6-2 connector): after 2 - 4 seconds, this closes the switch (5-4) which powers the electrical components of the appliance (only if the door is closed). The door interlock prevents aperture of the door while the appliance is in operation. At the end of the washing programme, the PCB disconnects the interlock from the power supply, but the door remains locked for 1 to 2 minutes (PTC cooling time). Certain models feature a pilot lamp which lights to indicate that the door is locked. This pilot lamp switches off when the door can be opened. Dado

The simplest way is to lay the washing machine on the right side so that you filter closer to the floor and from bottom of the washing machine is accessible drain pump. It can be fixed by three screws or just turn pump counter clockwise and pull out. Dado

From user manual: 10.4 At the end of the drying programme 1. The appliance stops automatically. 2. The acoustic signals operate (if they are active). 3. In the display (number "0") comes on. 4. The indicator of button Start/Pause goes off. 5. The last minutes of the drying cycle the appliance performs the anticrease phase. The anti-crease symbol flashes. The door is still locked (the key symbol is on). 6. Press button On/Off for some seconds to deactivate the appliance. After some minutes from the end of the programme, the energy saving function automatically deactivates the appliance. 7. When the door locked light goes off you can open the door. 8. Remove the laundry from the appliance. Make sure that the drum is empty. 9. Keep the door ajar, to prevent mildew and odours. 10. Close the water tap. If this doesn't help than check: - If the delay start is set, cancel the setting or wait for the end of countdown. - Deactivate the Child Lock function if it is on If anything of this doesn't help then pay attention to all the symbols appears on the display and check what it means in the user manual. Dado

After turn and choose cycle by program switch, press the Start / Pause button otherwise the program will not start. If you did everything right then the "Cd" should appear on the display, which means door lock failure. green = The door can be opened av = The door can not be opened at the moment red = Door is open Dado

Alarms EH1-EH2-EH3: In the event of problems with the power supply, the appliance remains in alarm mode until the voltage and frequency are restored to within the normal limits or the appliance is switched off. Alarm family "H" is displayed and it is not possible to access diagnostic mode nor to use the "rapid alarm display" function. The complete alarm can be read only when the abnormal condition has terminated. Dado

5.18 Child lock function This function prevents children operating the control panel. • To activate this function, touch button 12 and button 11 at the same time until the display shows the symbol . • To deactivate this function, touch button 12 and button 11 at the same time until the symbol goes off. You can activate the function: • Before you touch the button 6 : the appliance cannot start. • After you touch the button 6 , all the buttons and the programme knob are deactivated. Display: Dado

It sounds more like a heater fault where the heater is shorting out. Try disconnecting the heater and test it with a meter, put one terminal from the meter on either of the heater terminals and the other on the heater casing, if you get a reading the heater needs replacing. If there is no reading then reconnect the heater terminals and do the test again this will test through the heater wiring, it will at least give you some idea as to where the fault is.

I suggest checking the moister sensor and or cycling thermostat. the hi limit thermostat as well, with a meter for continuity. other wise you may have a bad timer

Select the program of draining or spinning. You should hear the drain working. If not, don't insist. Turn it off and pull the power cord out. After that, you should clean the filter of the appliance. This is located on the bottom of the front panel. Just watch out ..becuase when you unscrew the filter, all water will come out from there. Be sure you have a towel beside you! After the water comes out, check into the hole of filter if there is any object that blocks the pump to work. If you find something, perhaps you solved the problem! Here is the user instructions of how you can do it. AEG Lavamat 541 electronic Operating Instructions Manual

Do a wash with just bicarbonate soda then wipe it out, including any rubber seals

Replace your water pump ... probably working but impeller is too worn! Good Luck! Handy Henry If you need further help, I’m available over the phone at https://www.6ya.com/expert/henry_239f63a136de60f0

The E52 code indicates that the motor is not moving. This could mean the the carbon brushes have worn out, the entire motor is bad or that the wiring or control units have damage so that the message to spin is not getting to the motor. Take off the back of the washer (after unplugging it). Inspect the motor plug and wiring to that plug. If those look okay, take out the motor and inspect the carbon brushes. If those are worn or broken, then you need to replace them. If the brushes are okay, then the entire motor or the control board are more likely to have a fault. See http://shop.aeg.co.uk/search?prpp=20&ppn=1&psfo=A&filter=category%3ALaundry%3AWashing%2BMachines and use the full product number to find out the part numbers you may need. Other sites will have these parts. I hope this helps. Please add the product number of your AEG Lavamat 74810 if you need assistance finding parts. Cindy Wells

I looked up the list of error codes for this washing machine and sorry but e19 is not listed, it skips that one number. Please contact AEG.

Check detergent is properly inserted. if the tray is not fully in detergent will not dissolve and also water will spill. OR the water pipe may have pushed back.

1. E52 is a motor fault, i.e. motor not turning or tachometer is faulty. It is most likely that the carbon brushes are worn out and need replacing. These are readily available online

Here is link AEG ELECTROLUX EFG 540 User Manual

The circuit board the buttons are on has fallen off the faceplate bezel. Open the cabinet to see if a plastic tab has broken off or some other attachment has failed.

Intervention of motor overheating safety cut-out. Possible fault Motor faulty; Intervention of motor overheating cutout; Wiring faulty; Electronic board faulty. Machine Status/Action Power to the heater unit and reversal of the direction of rotation are interrupted. If the problem does not re-occur, the alarm is memorized and the cycle continues. If the fault persists after several attempts to supply power (about 35 min.), alarm E51 is generated.

suggestion, ring up AEG and ask for the technical department give them model and code and they should give you the answer your looking for good luck.