AEG Washing Machines - Answered Questions & Fixed Issues

Replace the watervalve.
Its stuck open

AEG Washing... | Answered on Sep 10, 2019 | 469 views

Hi from retired Englishman in SW France,

Sorry but this forum does not supply any type of manual or schematic diagram direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)

You will need to type into your search engine/web browser '(make) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount. During the process you will be asked for the actual model number!
Good luck,
John C

AEG Washing... | Answered on Aug 29, 2019 | 531 views

All I have is the drawing of the electrical circuit

AEG Washing... | Answered on Jul 05, 2019 | 786 views

Ertor E62

Power relay to heater unit faulty.

Possible fault Heater unit faulty; Wiring faulty; Electronic board faulty.

Machine Status/Action Forced cooling cycle.

AEG Washing... | Answered on Jun 16, 2019 | 43 views

Request the manual directly from AEG.

AEG Washing... | Answered on May 13, 2019 | 105 views

google AEG washing machine trouble shooting for answer.

AEG Washing... | Answered on May 04, 2019 | 35 views

google AEG flio661te gives water safety message for answer.

AEG Washing... | Answered on May 04, 2019 | 48 views

google AEG washing machine gives safety massage.

AEG Washing... | Answered on May 04, 2019 | 32 views

Maybe it helps something

AEG Washing... | Answered on Mar 02, 2019 | 53 views

test you water solenoids and replace if faulty

AEG Washing... | Answered on Feb 28, 2019 | 41 views

This could be the valves not opening all the way that could be due to mineral buildup, check the water pressure in the line and also check to make sure the proper voltage is getting to the valves and if all is ok, replace the valve assembly from any online spares centre.

AEG Washing... | Answered on Feb 03, 2019 | 79 views

Power supply problem. Try another plug in. If it still doesnt work you have a wiring problem.

AEG Washing... | Answered on Jan 31, 2019 | 35 views


AEG Washing... | Answered on Jan 24, 2019 | 444 views

Cd - means door lock defect so replace door lock or check cable and PCB (triac).


AEG Washing... | Answered on Jan 12, 2019 | 1,022 views

C1 - means that in prewash cycle no water inlet, valve does not open/ interruption or flow rate too low.
So I suggest to you following: check water inlet, clean sieve, check inlet valve, check pressure sensor and finally check wiring.


AEG Washing... | Answered on Jan 12, 2019 | 1,049 views

If there is a fault happend the error code should appear on the display (as shown picture below) :

error code will appears on display-x2i5s4yosfxg1xpsbuvvkqua-1-0.jpg There are two types of error code, first one that begins with a letter "C" and a mean customer fault code that can eliminate by the customer.
for example:
C1 - means "Telescopic runner inside during pyrolyse"
Remedy: "Remove side grids during pyrolyse"

Faults that begin with letter "F" require the expertise of a service technician especially when it comes to new ovens powered and controlled by electronics.

for example:
F 239 means: Quantum Touch Controller alarm:
1. If the communication over the bus SPI with the Quantum touch is after 50 trials unsuccessful than alarm is set. The alarm is reset if the communication is okay again.
Could be:
1. Connections Board Touch.
2. Board Touch fault.


AEG Washing... | Answered on Dec 30, 2018 | 47 views

Not finding what you are looking for?
AEG Logo

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 1 Expert

24 Answers

Vincent G
Vincent G

Level 3 Expert

2361 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides