AEG Washing Machines - Page 3 - Popular Questions, Answers, Tips & Manuals
My AEG washing machine W1037 washes perfect but do not spin the cloths comes out wet
Possible imbalance:
- When the washing machine will not spin, this may not be due to a fault on the machine. It may be due to the electronic balance check.
- The electronic balance check ensures that the clothing is balanced inside the washing machine before the appliance starts to spin. This prevents your washing machine from being subjected to uneven loads, which can damage the machine.
- The electronic balance check also means that your washing machine will not be able to spin a single garment or a few garments because it is unable to balance the machine. If the imbalance exceeds 0.5 kg, the spin function will not operate.
- In the case of a single garment or a few garments, there will be nothing wrong with the washing machine. You can work around the problem by placing a few towels in the washing machine. Towels help the washing machine to balance the load and spin.
- You can test your machine by spinning with an empty drum (without any garments). If this works, the machine is working properly.
- Overloading the machine can also cause the machine not to spin.
If none of the above suggestions resolve the problem, we recommend contacting an Authorized Service Center.
Rinse hold selected:
- If rinse hold is selected, the washing machine does not spin at the end of the cycle. If there is water in the machine after washing, select and start a pumping cycle.
Level:
- If the appliance has not been installed so that it is level, it may cause the machine not to spin. To level the appliance, adjust the appliance's feet and check it with a spirit level.
Unstable base:
- If the base on which the machine is placed is unstable, e.g. a wooden floor (not a solid level base), it may cause the machine not to spin. If the base is not level or firm, movements may occur in the machine which prevent it from balancing itself.
Dirty filter:
- If the drainage does not function properly, it may cause the machine not to spin. Clean the drain filter and the pump blade (if the pump blade is visible, turn it using a pencil and remove any fluff or foreign objects). Then refit the filter and start a hot wash without any soap to clean the machine. Check if the drain hose is set at the proper height (min. 60 cm - max. 90 cm) and if it is not put too far down into the drain (max. 10 cm).
The dispenser drawer on my AEG Lavamat is stuck half open and appears jammed. Help please
Open the machine up on the top lid. 2 screws at the back of the machine at the top. Slide the lid back and remove it. The drawer can now be accessed. There should be a bunch of clips holding the lid of the drawer . You can carefully open these clips to remove the lid or just remove the entire drawer assembly and replace it or try to figure out what is jamming it.
1/22/2018 10:16:09 PM •
AEG Washing...
•
1,308 views • 0 helpful votes
AEG Lavamat washing macine C9 error code
C9 is a motor fault.
Normally it's worn out carbon brushes so you'll need to check them first.
If worn out or broken, replace them.
Then, you need to erase the code (reset the machine).
To do this, turn the dial to off.
Press and hold together, prewash and soaking buttons.
While holding them, turn the dial 1 click anti clockwise.
Release the buttons.
Turn the dial to off, to any program and back to off.
This should get rid of the C9 code.
It will come back if you don't repair the motor fault.
12/10/2017 11:06:03 PM •
AEG Lavamat...
•
2,730 views • 0 helpful votes
AEG 73630: wont take water
The machine knows what the water level should be at every step of the program, so if its full when it should be empty, is not filling when it should be or is taking too long to fill or empty the program will abort and count down in seconds as you describe.
First - check the drain filter for blockage!! if clear, can you hear the drain pump running on 'drain' program? a chug chug chug noise. If not pump may be jammed or seized - or the drain tube maybe be blocked at the waste connection on the sink, etc. Or maybe the water supply pipes have blocked or got turned off? Possibly the waste pipe may not have been installed correctly and the machine is syphoning empty? ie the end of the waste pipe is lower than the water level in the machine - so it syphons empty like draining petrol from a petrol tank! That would empty the machine when it should be full.
Check all the basics of filling, draining and filter before suspecting anything else.
Not finding what you are looking for?
