AEG Washing Machines - Popular Questions, Answers, Tips & Manuals


Hi.
Replace the watervalve.
Its stuck open

AEG Washing... | 469 views | 0 helpful votes


Request the manual directly from AEG.

AEG Washing... | 105 views | 0 helpful votes


Ertor E62

Power relay to heater unit faulty.

Possible fault Heater unit faulty; Wiring faulty; Electronic board faulty.

Machine Status/Action Forced cooling cycle.

AEG Washing... | 43 views | 0 helpful votes


google AEG flio661te gives water safety message for answer.

AEG Washing... | 48 views | 0 helpful votes


google AEG washing machine trouble shooting for answer.

AEG Washing... | 35 views | 0 helpful votes


USUALLY THEY JUST PULL OFF . WITH SOME RESISTANCE OF COURSE , OTHERWISE THEY WOULD JUST FALL OFF

AEG Washing... | 444 views | 1 helpful votes


google AEG washing machine gives safety massage.

AEG Washing... | 32 views | 0 helpful votes


This could be the valves not opening all the way that could be due to mineral buildup, check the water pressure in the line and also check to make sure the proper voltage is getting to the valves and if all is ok, replace the valve assembly from any online spares centre.

AEG Washing... | 79 views | 0 helpful votes


test you water solenoids and replace if faulty

AEG Washing... | 41 views | 0 helpful votes


Maybe it helps something
https://www.manualslib.com/products/Aeg-Bs-45-3977008.html

AEG Washing... | 53 views | 0 helpful votes


Power supply problem. Try another plug in. If it still doesnt work you have a wiring problem.

AEG Washing... | 35 views | 0 helpful votes


If there is a fault happend the error code should appear on the display (as shown picture below) :

error code will appears on display-x2i5s4yosfxg1xpsbuvvkqua-1-0.jpg There are two types of error code, first one that begins with a letter "C" and a mean customer fault code that can eliminate by the customer.
for example:
C1 - means "Telescopic runner inside during pyrolyse"
Remedy: "Remove side grids during pyrolyse"

Faults that begin with letter "F" require the expertise of a service technician especially when it comes to new ovens powered and controlled by electronics.

for example:
F 239 means: Quantum Touch Controller alarm:
1. If the communication over the bus SPI with the Quantum touch is after 50 trials unsuccessful than alarm is set. The alarm is reset if the communication is okay again.
Could be:
1. Connections Board Touch.
2. Board Touch fault.

Dado

AEG Washing... | 47 views | 0 helpful votes


To display Error Code:
Move Programme Selector to the Off postion.
Press the 2 buttons on the right and turn the selector 1 position clockwise and hold the 2 buttons for about 5 seconds until all the lights are flashing. Release buttons and turn the selector to the 10th position. The Error Code will be displayed.
Note the code then turn the selector to off ,then on,then off again.

AEG Washing... | 132 views | 1 helpful votes


C1 - means that in prewash cycle no water inlet, valve does not open/ interruption or flow rate too low.
So I suggest to you following: check water inlet, clean sieve, check inlet valve, check pressure sensor and finally check wiring.

Dado

AEG Washing... | 1,049 views | 0 helpful votes


Cd - means door lock defect so replace door lock or check cable and PCB (triac).

Dado

AEG Washing... | 1,022 views | 0 helpful votes

Not finding what you are looking for?
AEG Logo

1,530 questions posted

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

sami

Level 1 Expert

24 Answers

Vincent G
Vincent G

Level 3 Expert

2361 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...