At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
I think i have a bad control broad. when i plug the washer in it does nothing.
your can push all the control buttons and will not light up. If I push the
stop/ cancel botton , it stays on dilicate mode. I can push all the buttons and it will not change the setting and can not start it.
I have a Kenmore Elite that was workinig perfectly until yesterday. Put in a load and cannot get it started. The buttons are all nonresponsive. Checked the outlet and there is power coming in. Any help is appreciatedI have a Kenmore Elite that was workinig perfectly until yesterday. Put in a load and cannot get it started. The buttons are all nonresponsive. Checked the outlet and there is power coming in. Any help is appreciated
AnonymousMar 18, 2008
The "controls locked" button is lit and the machine will not do anything. I've tried pushing all other buttons and have unplugged machine. Nothing is working. My model #44936.The "controls locked" button is lit and the machine will not do
anything. I've tried pushing all other buttons and have unplugged
machine. Nothing is working. My model #44936.
You can't post conmments that contain an email address.
It certainly does sound like the main control, this is the most common part (electronically speaking) also there is the display board(s) directly behind the control panel. This PC relays user inputs to CCU (located on top of washer ---middle rear). I havent replaced a faulty display board yet out of the 50+ ive serviced. Doesnt mean its not bad. If you have any questions feel free....
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1. Unplug washer or disconnect from power.
2. Check wire harness between drive motor and MCU. Between MCU and CCU. Check the motor and do a continuity test.
3. Plug in washer or reconnect power.
4. Check the MCU by looking for operations of the drive motor.
5. Check the drive motor for powered rotations.
6. Replace the MCU board.
its the power button its a common prob use a soldering iron and switch it with the load sinal button this happpens as the washer alallows moisture to get on the board as its not protected it will save u a ton of money and anyone can do it
I have a Kenmore HE5 Steam: after a power failure last week, now when you turn the dryer on and push"start" the cycle stops emediately and flashes PF...
I continued to push the set delay and end of cycle buttons, twice. Then I pushed the jeans cycle button and let it run its course. After doing that twice, it drained the drum and I tried to start a new cycle for washing, which worked. Yea!
This is usually a symptom of a bad motor control board which located under the console. I had the same problem. You can open the console by removing the three screws in the back and lifting from the rear first. The console will pop off. In addition, if you look along washer top front edge in the seam there is a retaining clip about 2 inches in from each side. Using a putty knife, push in on each clip while lifting and the top should pop up. There will be a tech sheet affixed to the front wall of the washer between the wash tub and case. This tech sheet will give you all the guidance necessary on how to perform tests to prove whether or not the motor controller is at fault, or if the pump is at fault. I believe you may have a motor controller problem, though. Another possibility is getting something caught in the drain pump reservoir. This could binding the pump. Let me know if any of this is helpful to you.
I have a Kenmore Elite that was workinig perfectly until yesterday. Put in a load and cannot get it started. The buttons are all nonresponsive. Checked the outlet and there is power coming in. Any help is appreciated
The "controls locked" button is lit and the machine will not do
anything. I've tried pushing all other buttons and have unplugged
machine. Nothing is working. My model #44936.
×