How do I set my Aquastar Model no. 4097 solar powered watch?

make sure the dial is pressed all the way in

Press "MODE" and above it "SET" and it should help you re-set the time correctly.Hope this helps!

Hi,

Hope this will helped you fixing the time of your Citezen divers watch. Just foolow the instruction below.

Change your Citizen watch's time zone without actually moving the clock hands. On the digital display, change the city that displays on the watch, which sets the time to the different time zone. The Citizen also has a calendar, timer, chronograph and LED lights. Since it is an Eco Drive watch, it is solar powered so you never have to replace the batteries unless its backup power source dies.
Difficulty: Easy Instructions

1. Pull the setting knob (crown) out one "tick" for setting mode.
   

2. Set the mode hand to "WT-S."
   

3. Pull the crown out one more "tick."
   

4. Press the top button on the right side of the watch for the city setting mode.
   

5. Press the lower button on the right side to "SET" the city.
   

6. Turn the crown to select a different city, which changes the time zone.
   

7. Push the crown all the way back in to finish setting the time.
   

Thank you for using Fixya.

Thank you for contacting FixYa.

Set Digital Watch
1. Press and hold the "Mode" button on the right side of your Arnette digital watch for three seconds to change the watch's mode. Press and hold the "Mode" button repeatedly until flashing digits indicate that you have entered the watch's time-setting screen.
2. Use the top and bottom buttons on the left side of your Arnette digital watch to increase and decrease number values as desired.
3. Press and hold the "Mode" button repeatedly to exit the time-setting screen and return the watch to time-telling mode.
Set Analog Watch
4. Pull out the watch crown on the right side of your Arnette analog watch.
5. Turn the watch crown clockwise to adjust the hands of your Arnette analog watch to the appropriate time.
6. Push the watch crown back in when you are finished setting the time on your Arnette analog watch.

Best regards. Jewel

Hi,

A lot of users are having trouble getting this watch going. Timex has two ways to find information about your particular watch. Some of these models only have a guide consisting of a few pages. If you don't have the manual, Try this link:
Direct link for the W-207 movement:
http://assets.timex.com/user_guides/W207_M115/W207_M115_NA_EN.pdf

Complete Timex link site:
http://www.timex.com/info/Product_Instruction_Guides_Downloads

Now, look up the model number, or if you cannot find that, check the three-digit Module Number from the back of the watch. Click on it in the Module Table, and download a PDF of your watch setting-instructions/manual.
If you need further help, call Timex in Little Rock, Arkansas, phone 1-800-448-4639.

I hope this helps you. Thanks, Bill

The catalogue says "never needs a battery" and as it is a "radio controlled " type, then it must have a battery that is charged by power generated by motion.

To get the watch to go, then you should wave it backwards and forwards for some time ( 100's of times according to one maker!). This will charge the battery.

Leave the watch overnight so that it can pick up the timing signal and correct the watch. I did this with mine when the battery was changed and it lost its time and it took a couple of days before it told the right time, so be patient.

If the watch refuses to show any sign of life, then it should be returned to an authorised repair agent for inspection.

this is a low battery warning indicator, all you need to do is have your battery changed, or if it is a solar powered watch just set it under a bright light to let it charge the rechargable battery.

I just picked up this watch.  Setting it is easy.  Hold down the button marked "RESET" (lower right) until the numbers start blinking.  Hit the "MODE" button (lower left) until the the settings you want to change are blinking.  Hit the "ST/STP" button (upper right) to change that setting.  Keep on hitting these two buttons until the settings are as you would like them.  Hit "RESET" button to finish.  So, to change just the day, I would hold down "RESET," hit "MODE" four times, hit "ST/STP" until the date is correct, hit "RESET" to save.  

joe WANT TO KNOW HOW TO SET THE TIME AND DATE ON A AQUASTAR WATCH# 3876.

How to set the solar power time change, my watch has remained with the same time; and not one hour ahead (spring forward) ?