AEG Lavamat Lavalogic 1600 Front Load Washer - Answered Questions & Fixed issues

is your inlet water pipe pointing straight down?i have read the instruction manual for this machine and it says to have the inlet water pipe turned 90 degrees to the left or right. is the rubber seal firmly in place? hope this helps..

C5 generally indicates a motor fault, specifically overheating. things that might make motors overheat are worn bearings and restricted ventilation

Hello I need to number kushintës Lavalogic AEG 1600 washing machine

Thanks for choosing FixYa and welcome. What all is the washer doing or not doing?

Hi,

The fault code indicates a motor fault.
Unplug the appliance from the wall socket before beginning.
Check the carbon brushes in the motor, this is the most common cause of the fault.
There is one carbon brush either side of the rear of the motor.
You will have to take the motor out to check them, unless you are very nimble and can do it from underneath while the machine is tipped back 45 degrees.

You'll probably find the carbon brushes are worn out.
If you can identify them from the pictures on Ebay, you'll be able to order them and save money on them too.

http://shop.ebay.co.uk/items/?_nkw=aeg+carbon+brush&_sacat=0&_fromfsb=&_trksid=m270.l1313&_odkw=lav72620&_osacat=0

If you email the seller they should be able to tell you which ones fit your model.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

I also have problems with AEG Lavalogic 1600. It is caused by the control knob and the poor contacts. One service repair person fixed it and lasted 1 month. Then the problem reappeared. Now, I turn on the knob and the machine does not turn on, but I push lightly the button, not to a full path, just to cause a contact and it starts.

Hello,

E10 relates to low water pressure normally or a fault with the inlet valves.You can check by turning off the water and taking off the hoses at the valve and check if the little filter is clogged,older machines have hot and cold water newer only cold.if they are ok then check at the other end of the hoses you may find a small very fine mesh filter come seal inside the nut of the hose be very careful if you remove them as they can get damaged,remove and rinse under tap and scrub with nail brush.If all clean make sure that the hoses have not been kinked and stopping the supply.An easy way to check if pressure is good is to put your thumb over end of cold supply and switch on over a container if you can hold your thumb on easily pressure is not good if you get wet then its ok.(not very scientific I know but simple).IF there is still a problem then you will have to check each solenoid on the valves with a meter for contniuity these coils can burn out but are quite easy to replace as long as the the mechanical part of the valve is ok.Normally you can only buy them as a complete package.Check these out and hopefully it was helpful.

Good Luck.

check out the drive belt

The best way to check is to remove the belt, and spin the drum by hand.
If it feels rough or is rumbling, then the main bearings have failed.

Check two things:
Clean your strainer, located behind the kick panel at the lower front of the machine. It will be in between the drum and the pump, and will have a lid that unscrews.
Check your Drain Hose: The easiest way is to remove it from the house drain, and empty it into a bucket. If at all possible, point it outside and run a cycle with fresh water only.
The strainer will probably fix you up, and usually makes the clothes smell better too.
Best regards, --W/D-- please feel free to rate this solution..thanx!

LOOK IN YOUR MANUAL...IT SHOULD HAVE A SOLUTION TO THIS CODE..JUST FOLLOW INSTRUCTIONS...BEST OF LUCK..

open the filter door at bottom turn screw with coin , door should open ,

Question edited for clarity and spelling. Question moved to maker category. Very easy. https://www.google.com/search?q=AEG+Lavamat+509+Washing+Machine.+How+to+replace+pump ..

Yes, the most likely reason is that the pipe has a blockage, the bore isn't large enough, you have an airlock with water in it, or the fall into the waste pipe isn't steep enough. When it senses any back pressure it faults. ..

Pease don't type in all CAPS Anonymous, it is considered SHOUTING and is harder to read. It is a motor circuit fault

I have a AEG Lavamat 72800 which doesnt start any cicle ...

JustAnswer https://www.justanswer.com > UK Appliance Repair Oct 13, 2011 - Hi. Ok lets get the correct error code out. To do this turn the dial to any setting and let it light up. Then press and hold the rinse hold ... 1 answer · Top answer: Hi Ok E54 means motor relay contacts sticking or motor down to earth. The relays are ...

I keep getting a error E50 on my AEG Lavamat model ...

JustAnswer https://www.justanswer.com > UK Appliance Repair Jul 5, 2012 - E50 is a motor circuit fault. Check the carbon brushes again, see if they've broken or stuck. Check the wiring to the motor. Let me know ... 1 answer · Top answer: Hiya, E50 is a motor circuit fault. Check the carbon brushes again, see if they' https://www.google.com/search?q=AEG+LAVAMAT+72800+ERROR+CODE+50 ..

E21 means a blockage in the drain pump. I would check the impeller spins freely. A coin from a pocket can cause that error as it gets stuck in the impeller.

Check out all the videos Linda. https://www.google.com/search?q=replace+AEG+washing+machine+door+seal ..

The collaboration between traditional and digital artists in the NFT space is breaking down barriers and fostering creativity.

Download the manual from following link Aeg LAV2442 User Manual ' Manualzz