20 Most Recent AEG Lavamat W1050 Front Load Washer - Page 7 Questions & Answers

Contact AEG to see if one if available to consumers. https://www.aeg.co.uk/support/ Support

Not all of the options on the AEG Lavamat L64850 are available with every cycle. The Time-savings option isn't compatible with the 40-60 Mix program. See ManualsLib, https://www.manualslib.com/manual/555025/Aeg-Lavamat-L64850l-7kg.html?page=16#manual , for the various washing programmes and the available options. You can get the full manual for your washer at AEG, https://www.aeg.co.uk/support/download-manuals/ . There are several models listed. The direct link to the manual for the L64850L/91452556002 is currently http://www.electrolux-ui.com/DocumentDownLoad.aspx?DocURL=2013\132\950431EN.pdf . I hope this helps. Cindy Wells

What is a "drayaer"?

Possible imbalance:

• When the washing machine will not spin, this may not be due to a fault on the machine. It may be due to the electronic balance check.
• The electronic balance check ensures that the clothing is balanced inside the washing machine before the appliance starts to spin. This prevents your washing machine from being subjected to uneven loads, which can damage the machine.
• The electronic balance check also means that your washing machine will not be able to spin a single garment or a few garments because it is unable to balance the machine. If the imbalance exceeds 0.5 kg, the spin function will not operate.
• In the case of a single garment or a few garments, there will be nothing wrong with the washing machine. You can work around the problem by placing a few towels in the washing machine. Towels help the washing machine to balance the load and spin.
• You can test your machine by spinning with an empty drum (without any garments). If this works, the machine is working properly.
• Overloading the machine can also cause the machine not to spin.

If none of the above suggestions resolve the problem, we recommend contacting an Authorized Service Center. Rinse hold selected:

• If rinse hold is selected, the washing machine does not spin at the end of the cycle. If there is water in the machine after washing, select and start a pumping cycle.

Level:

• If the appliance has not been installed so that it is level, it may cause the machine not to spin. To level the appliance, adjust the appliance's feet and check it with a spirit level.

Unstable base:

• If the base on which the machine is placed is unstable, e.g. a wooden floor (not a solid level base), it may cause the machine not to spin. If the base is not level or firm, movements may occur in the machine which prevent it from balancing itself.

Dirty filter:

• If the drainage does not function properly, it may cause the machine not to spin. Clean the drain filter and the pump blade (if the pump blade is visible, turn it using a pencil and remove any fluff or foreign objects). Then refit the filter and start a hot wash without any soap to clean the machine. Check if the drain hose is set at the proper height (min. 60 cm - max. 90 cm) and if it is not put too far down into the drain (max. 10 cm).

Hello! Probably you have foreign stuff in the drain pump or the pump worn out. Unplug the machine and unscrew the pump cap, watch for water pouring out, prepare something to catch in the water, then inspect for coins, knobs, ... . Check if the pump wheel rotates freely. screw back the cap and try to start a new wash program

The machine knows what the water level should be at every step of the program, so if its full when it should be empty, is not filling when it should be or is taking too long to fill or empty the program will abort and count down in seconds as you describe. First - check the drain filter for blockage!! if clear, can you hear the drain pump running on 'drain' program? a chug chug chug noise. If not pump may be jammed or seized - or the drain tube maybe be blocked at the waste connection on the sink, etc. Or maybe the water supply pipes have blocked or got turned off? Possibly the waste pipe may not have been installed correctly and the machine is syphoning empty? ie the end of the waste pipe is lower than the water level in the machine - so it syphons empty like draining petrol from a petrol tank! That would empty the machine when it should be full. Check all the basics of filling, draining and filter before suspecting anything else.

Check your pressure sensor. Make sure that the air column that operates the pressure sensor is not blocked. Find the pressure sensor and remove the air hose to it. Blowing into it with the hose attached to the pressure sensor will check the pressure sensor. Use an ohm meter to measure if it changes. Blowing on it with it connected to the air column will check that nothing is blocking it.

This sounds like it is the heating element in the machine. Check to make sure the heating element is getting power. If it is then replace the element.

This could be a number of issues. Have you checked the brushes? They should be at least 15mm. Check your circuit board and make sure that the dust from the brushes did not attach itself to the board and cause a short. Use compressed air to clean the motor. Clean the circuit board with air if dirty. Check for solder joints on the circuit board to see if any cold solder joints on the relays.

Is it plugged in? Is the water on? Is the door closed?

Open the machine up on the top lid. 2 screws at the back of the machine at the top. Slide the lid back and remove it. The drawer can now be accessed. There should be a bunch of clips holding the lid of the drawer . You can carefully open these clips to remove the lid or just remove the entire drawer assembly and replace it or try to figure out what is jamming it.

5.18 Child lock function This function prevents children operating the control panel. • To activate this function, touch button 12 and button 11 at the same time until the display shows the symbol . • To deactivate this function, touch button 12 and button 11 at the same time until the symbol goes off. You can activate the function: • Before you touch the button 6 : the appliance cannot start. • After you touch the button 6 , all the buttons and the programme knob are deactivated. Display: Dado

go to the manufactures website and download the user manual for advice on error codes eric

my best advice is to call the engineer for a quote as there's obviously a problem in the making after further use eric

go to the manufactures website for help this is a washing machine help website eric

Im sorry to say that you will need to cal the AEG engineer for a quote as the display cannot be black, it should display some information on start up anyway eric