AEG LW1250 Front Load Washer - Answered Questions & Fixed issues

Check the brushes on the motor. They should be at least 15mm long. Remove back panel, and remove motor (watch the wiring orientation). Then remove the brushes. If they need replacing get new ones and then blow out the entire motor from the carbon dust created by the brushes with compressed air.

Please check on this link : front panel

Hi from retired Englishman in SW France,
(this is my standard, pre-typed response to this sort of problem, sorry)

It does sound as if the motor requires replacement unless it is the control board not powering the motor.
Now, a word or two of advice from a retired Englishman in SW France. It might be suggested that just the brushes on the motor want changing; experience (of others) suggests that they may only last months rather than many years UNLESS the motor itself is refurbished. Refurbishment includes skimming the commutator on which the brushes run. Without skimming the brushes do not sit cleanly on the com, often causing excessive sparking and excessive wear on BOTH. Alternately a new motor! I changed the motor on our 19+ year-old Bosch at a cost of GBP250 ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

possible interlock, the switch that stops it from working when the door / lid is open start here

Question edited for clarity and spelling. Question moved to maker category. Very easy. https://www.google.com/search?q=AEG+Lavamat+509+Washing+Machine.+How+to+replace+pump ..

Yes, the most likely reason is that the pipe has a blockage, the bore isn't large enough, you have an airlock with water in it, or the fall into the waste pipe isn't steep enough. When it senses any back pressure it faults. ..

Pease don't type in all CAPS Anonymous, it is considered SHOUTING and is harder to read. It is a motor circuit fault

I have a AEG Lavamat 72800 which doesnt start any cicle ...

JustAnswer https://www.justanswer.com > UK Appliance Repair Oct 13, 2011 - Hi. Ok lets get the correct error code out. To do this turn the dial to any setting and let it light up. Then press and hold the rinse hold ... 1 answer · Top answer: Hi Ok E54 means motor relay contacts sticking or motor down to earth. The relays are ...

I keep getting a error E50 on my AEG Lavamat model ...

JustAnswer https://www.justanswer.com > UK Appliance Repair Jul 5, 2012 - E50 is a motor circuit fault. Check the carbon brushes again, see if they've broken or stuck. Check the wiring to the motor. Let me know ... 1 answer · Top answer: Hiya, E50 is a motor circuit fault. Check the carbon brushes again, see if they' https://www.google.com/search?q=AEG+LAVAMAT+72800+ERROR+CODE+50 ..

E21 means a blockage in the drain pump. I would check the impeller spins freely. A coin from a pocket can cause that error as it gets stuck in the impeller.

Check out all the videos Linda. https://www.google.com/search?q=replace+AEG+washing+machine+door+seal ..

The collaboration between traditional and digital artists in the NFT space is breaking down barriers and fostering creativity.

Download the manual from following link Aeg LAV2442 User Manual ' Manualzz

AEG Fault codes.... https://www.northlondonappliancerepairs.co.uk/error-codes/aeg-error-codes/error-codes-for-aeg-washing-machines.html Tis quite a way down the list.

Please start with your clothes after the washer finishes it's washing cycle. Take them out and see how dry they are. They should be nearly dry. If not, perhaps the reason you are having problems is they are too wet to begin with for the dryer to properly do it's job.. This is not a rare problem. One possible reason for the clothes not to be dry when the washer finishes is a loose or worn out belt under the washer. Another problem some washers have, particularly washer/dryer combos, is that they are sometimes not very effective. In that case, either smaller loads or rerunning the spin cycle at the end of the washing cycle might help you. God bless your efforts.

Nearly ever manual is available online, but 22 litre is a size not a model number. My search query is pointing to Dishwashers with water softeners. The search query is 'make model manual', nothing else. https://www.google.com/search?q=AEG+22L+water+softener ..

To remove the plinth on your AEG FFE62620PM dishwasher, please follow these steps:

1. Turn off the power supply to the dishwasher by unplugging it or turning off the circuit breaker.
2. Open the dishwasher door and locate the two screws on the bottom of the plinth. These screws are located on either side of the dishwasher and are usually covered by plastic caps.
3. Remove the plastic caps and use a screwdriver to unscrew the screws.
4. Pull the plinth away from the dishwasher to remove it. It may be helpful to have someone hold the dishwasher steady while you do this.
5. Once the plinth is removed, you should be able to access the base of the dishwasher and any components located there.
6. If you need to reinstall the plinth, simply reverse the above steps.

Error code E6H on your AEG Lavamat washing machine typically indicates a problem with the heating system. It may mean that there is a problem with the heating element, the temperature sensor, or the control board. It's best to refer to the manual for your specific model for the exact meaning of the error code and for further instructions on how to resolve the issue. If you are unable to resolve the issue yourself, it is recommended that you contact a professional repair service for assistance. Attempting to repair a washing machine can be dangerous and may void your warranty if not done properly.

It sounds like your AEG Lavamat 86850 washing machine may be experiencing an issue with the power supply. Here are a few steps you can try to troubleshoot the problem:

1. Check the power cord and plug for any visible damage. If the cord or plug is damaged, it may need to be replaced.
2. Check the outlet that the washing machine is plugged into to make sure it is functioning properly. You can test the outlet with a different appliance to determine if it is the source of the problem.
3. Check the fuse or circuit breaker that is connected to the washing machine. If the fuse has blown or the circuit breaker has tripped, it will need to be reset or replaced.
4. If the issue persists, it is possible that there may be a problem with the internal wiring or electrical components of the washing machine. In this case, it will likely be necessary to have a qualified technician inspect the machine to diagnose the problem and recommend the necessary repairs.

I hope this information is helpful. Let me know if you have any other questions or if there is anything else I can assist with.