Hoover SteamVac F5914-900 SpinScrub Upright Vacuum - Answered Questions & Fixed issues
Spin brushes do not turn
Hi There,I\'ve written an extensive
repair solution on how to diagnosis Hoover SteamVac\'s when the brushes stop spinning. A lot of the times the brushes just need to be cleaned, or it could also be the turbine assembly inside.Here\'s a link to the diagnosing:
http://www.fixya.com/support/t4286338-hooverspin_scrub_brushes_always_stopAnd if you find out that you need to replace the turbine, here\'s a link that shows you step by step how to replace the turbine:
http://www.fixya.com/support/r4530769-diagnosis_fix_hoover_steamvacs_whenHopefully these were helpful to you. Please be so kind and rate the repair helpful, or leave feedback for me if you found this helpful. This is really appreciated by the Fixya community to do if this was able to fix your problem, and ensures that Fixya experts continue to post free repair solutions rather then just answering the premium questions.Thanks so much,
How can I install recovery tank latches on Hoover Steam Vacuum model F-220?
To install the recovery tank latches on a Hoover Steam Vacuum model F-220, follow these steps:
- First, make sure that the recovery tank is empty and that the machine is turned off and unplugged.
- Locate the two latch slots on the sides of the recovery tank. These are the slots where the latches will be installed.
- Hold one of the latches with the clip facing up and the open end facing the latch slot.
- Insert the latch into the latch slot, making sure that the clip is facing towards the front of the machine.
- Repeat this process for the other latch on the opposite side of the recovery tank.
- Once both latches are installed, close the recovery tank and make sure that it is securely locked in place.
I hope this information is helpful! Let me know if you have any other questions.
How do I clean the hoover steam vac floor cleaner
Nozzle Clean Out tool is NO LONGER AVAILABLE from Hoover. Hoover stopped making this part over 1 year ago, and it's not sold any more. What you'll need to do is remove the dirty solution thank, unscrew the one silver screw on the suction port of the clear window, then turn the machine upside down and remove the two silver screws on the bottom corners of the see thru window. This will then allow you to completely remove the see thru part to clean inside of it. Unfortunately with this model that's really the easiest way to do it now that the tool is no longer available.
I have oak floor and there are scuff marks. Is it...
If you have a wax finish you can buff out scuffs with just a cloth. for polyurethane, do not use water. use the cleaner with a soft terry cloth. to much presure can make it worse.you can also use a small amount of paint thinner on polyurethane. make sure you remove excess with floor cleaner.
Hoover spinscrub 50 won't spray water/shampoo
'recovery tank not seated properly'....
Ty so much for posting this!! I swear I was just about to take this thing apart, but decided to take a break first and Google some options. And wudayaknow...someone describing EXACTLY what my machine was doin'. With the air blowing underneath and everything. Because it's never that simple for me, whenever I go to the all answering internet for help, it always ends up that I'm the only 1 on earth that has this problem. LoL. So thank you thank you thank you. I guess I'll get use my brand new Makita power screwdriver(???? Power drill??? It was a gift.lol) another time .
The brushes on my F7206-900
All I'm wondering is how to get the back plastic by the wheels off? I can't find any screws! This older model isn't like the ones shown on Internet sites. Seems they simplified the model, which is a good thing.
Cleaning uphoustry
Furniture cleaning isn't a science: try out a few techniques before choosing the one that is right for your belongings. This step-by-step guide explains how to clean a sofa:
- Before using any upholstery cleaning products, vacuum the sofa or chair first to remove as much surface dirt and dust as possible. Be sure to use the correct attachments to avoid damage to the material - a soft brush attachment is ideal.
- Spot Clean. Using baby wipes or vinegar poured onto a strong microfiber cloth, apply to any obvious stains, wiping gently as you go. Remember to test the upholstery cleaning products on an inconspicuous area first.
- Overall Clean. Using soapy water and a microfibre cloth, gently wipe your sofa with the solution, allowing it to soak into the fabric and tackle the dirt beneath the surface. You only want to use a very small amount of water - don't saturate the material.
- Dry. Some people use a hairdryer to quickly dry a sofa, but allowing it to dry naturally is always the better option, if you have the time. To speed things up, open windows and allow the breeze to help with the drying process.
House Office Carpet Residential Commercial Cleaning Geelong Commercial...
On hoover steam carpet cleaner,
Follow these steps if the Brushes Fail to Spin
•If the brushes on your Hoover carpet cleaner fail to spin, there may be a problem---some sort of blockage---with the suction or with the belt that turns the brushes.
Turn the Hoover carpet cleaner over, and inspect the brush area. Debris, strings, or pet hair may be tangled in the rollers, keeping them from turning. Use a pair of scissors to cut away any obstructions in this area. Flip the Hoover carpet cleaner back over, and turn it on to see if cleaning the rollers has solved the problem.
To check the belt, turn the Hoover carpet cleaner over, and remove the bottom plate screw with a Phillips head screwdriver. Investigate the belt area to see if it is broken or has somehow slipped off. If it is broken, you can order a part from Hoover.com or from many of the other online parts stores.
When the belt arrives, simply slide it on in place of the broken belt, reattach the bottom plate and turn the Hoover carpet cleaner right-side up. Turn it on to test your solution.
Brushes won't spin
First, please be sure to unplug your Steam Vac and remove both the clean water and the dirty water tank.
There should be a square stem that sticks up in the center of your brush assembly. If this stem is broken you will need to replace the complete brush assembly. If the stem is good; turn your cleaner on it's side and check in the area where the brush assembly goes (with the brush assembly removed). In the center of this area there is a square hole where the stem from the brush assembly goes. The square hole is in the bottom of the turbnie that spins your brushes. Using a large flat blade screw driver (not so large that you'll damage the hole), stick it in to the square hole and try to spin it. It should spin freely, if it is very hard to spin or won't spin at all, your turbine is bad and will need to be replaced.
Hoover part number for brush assembly:48437022
Hoover part number for turbine: 43191008
How do I repair a non-functioning solution trigger
The trigger has tabs on each side that snap into slots in the handle so that the trigger pivots in the slots. The slots where the trigger pivots may have broken, if so the trigger will not push the valve open and allow the water flow. If the tabs are broken you will need to replace the upper handle. If you supply me with your model number I will determine the proper part for your model.
Why does my hoover steam vac only blow out
Hey there! The cleaner blowing out air instead of sucking is an indication that the unit is not sealed off properly. Follow these brief steps to restore suction to your cleaner.
1.
Remove the clean water tank.
2.
Recline the handle and let the cleaner lay flat.
3.
Remove the dirty water tank lid.
4.
Reposition the front panel located on the outside of the tank in the center. It should be flush to the tank, even straight across and pushed down as far as it will go.
5.
Assemble the dirty water tank lid back on from the front to the back. The lid should not lift up from the front.
Give it a try! The cleaner should now have suction. Hope this helps!
Not finding what you are looking for?