Top 20
Sunpentown WC-30U Under-Counter Wine & Beverage Cooler 32-bottles NEW - Page 3 Questions & Answers
Can you use 12/2 romex for low volage lighting
Technically, NO.
Using Romex cable inside a buried conduit is NOT ACCEPTABLE as a buried conduit is considered a damp location due to the potential for water condensation inside the conduit and Romex is not rated for wet or damp locations.
To meet code requirement for conductors inside a conduit you'll need to meet 3 major requirements
1. All conductor insulation must be rated to the highest voltage of any circuit inside the conduit.
2. A buried conduit is a damp location.
3. Conduit capacity restrictions.
4/12/2023 3:24:37 AM •
Electrical...
•
53 views • 1 helpful votes
Predator 3500 AC Generator. Error 5 code. What does it mean?
Error code 5 on a Predator 3500 AC generator typically indicates an issue with the generator's fuel system. The error code may be caused by a problem with the fuel pump, fuel filter, fuel hose, or fuel tank. It could also be caused by a problem with the generator's carburetor or fuel injection system.
To troubleshoot the error code 5 on your Predator 3500 generator, you can try the following steps:
- Check the fuel level in the tank. If the tank is empty or low on fuel, fill it up and see if the error code goes away.
- Inspect the fuel hose for any cracks, kinks, or leaks. Make sure the hose is properly connected to the fuel tank and fuel pump.
- Replace the fuel filter if it is clogged or damaged.
- Check the fuel pump for any issues. The fuel pump may be malfunctioning or damaged, or it may not be getting enough power.
- Check the carburetor or fuel injection system for any issues. The carburetor or fuel injectors may be clogged or malfunctioning, or there may be a problem with the fuel pressure.
If these steps do not fix the error code 5 on your Predator 3500 generator, it may be necessary to consult a mechanic or the manufacturer for further assistance.
1/3/2023 4:43:57 AM •
Electrical...
•
602 views • 0 helpful votes
My ryobi rg-2600i does not have a reset button. How do i reset the overload
- Unplug any appliances or devices that are connected to the generator.
- Turn off the fuel valve, and let the generator cool down for at least 10 minutes.
- Check the oil level in the generator, and add more oil if necessary.
- Check the air filter and clean or replace it if it is dirty.
- Turn the fuel valve back on and start the generator.
- Check the spark plug to make sure it is in good condition and properly seated. If it is dirty or damaged, clean or replace it.
- Check the fuel line to make sure it is not clogged or damaged. If it is, replace it.
- Check the fuel filter to make sure it is not clogged. If it is, clean or replace it.
- Check the carburetor to make sure it is clean and functioning properly. If it is dirty or damaged, clean or rebuild it.
- Check the voltage regulator to make sure it is functioning properly. If it is damaged, replace it.
- Check all of the connections on the generator to make sure they are secure and not damaged.
- Check the generator's fuel tank to make sure it is full and that the fuel is fresh. If the fuel is old, it may have gone bad and will not burn properly.
- Check the generator's battery to make sure it is charged and functioning properly. If the battery is dead or damaged, the generator may not start.
- Check the engine for any visible signs of damage or wear. If you see any cracks, leaks, or other issues, the engine may need to be repaired or replaced.
- I know it is a basic checklist... I just hope that I might have thought of something that you did not? two minds are better than one... sometimes.
1/8/2023 9:59:07 AM •
Electrical...
•
312 views • 0 helpful votes
Model 1001 311 060 Motion security light
Try setting DUAL BRIGHT to OFF.
Be sure daylight sensor is clear.
Try putting unit into test mode and it should be full ON or full OFF. If not, then likely unit is bad.
3/29/2023 7:45:22 PM •
Electrical...
•
39 views • 0 helpful votes
I am replacing an old dimmer with a new one.
Easiest Way to Replace a 3-Way Switch
If you're simply swapping an old 3-way switch for a new one, use this simple trick to get the wiring right: Before disconnecting any wires on the old switch, find the wire attached to the common screw terminal and label it with a piece of tape. Then, you can disconnect all three wires from the switch, as well as the ground wire. Because the other two wires (the travelers) are interchangeable, it doesn't matter which of the traveler screws you attach them to-there's no need to label them.
3/20/2023 2:38:15 PM •
Electrical...
•
47 views • 0 helpful votes
Why is my SaniFlo Saniaccess 2 tripping my GFCI constantly?
GFCI or RCD tripping is either moisture has entered the motor body or there is a wiring fault.
Neither of which would I consider a warranty issue especially noting the age.
Call an electrician to diagnose the fault first then take it from there.
2/19/2023 2:31:34 PM •
Electrical...
•
67 views • 0 helpful votes
How do you adjust a fiber cleaver?
Fiber cleavers are used for cleaning and breaking up fiber (straw) during the production of the finished product. They are most often used to clean the final processed fiber or to break up the straw before it is used to make the finished product. Here is a very basic, straightforward answer to this question. If the blade is dull, you have to sharpen it with a stone. A fiber cleaver's head is usually operated by a lever and has a screw mechanism to adjust the angle. A fiber cleaver is the best tool for pottery and ceramics. Want to know more visit our websites.
https://fibresales.com.au/test-termination-measurement/fusion-splicer-products/cleave-tool
2/10/2023 3:37:34 AM •
Electrical...
•
47 views • 0 helpful votes
Not finding what you are looking for?