Torque setting cylinder head bolt 4 cylinder KIA sportage

In the link

https://www.google.com/search?q=2005+Kia+Sportage+2.0+head+bolt+torque+settings&rlz=1C1QJDB_enCA643CA644&sxsrf=ALiCzsYoYU4KhT1GKZDXEa4PhY1dAFmXPg:1665344043608&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjYnJeB8tP6AhVkjIkEHfYvDd0Q_AUoAXoECAEQAw&biw=1920&bih=937&dpr=1

..

In the link

https://www.google.com/search?q=2007+Kia+Sportage+2l+Petrol+Se+head+bolt+torque+settings

..

What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

If you change the head bolts that's the safest bet for trouble free operation. But, I've changed head bolts on Hondas for years and they never stretched. I know this is for a Kia. My best guess is that it's not necessary since the Chilton based manuals don't say to do this.

If the head is torqued down to specifications and it leaks, then I would say, otherwise. Even torque is more important than bolt stretch, especially if the bolts don't stretch so much that the head gasket can't be tight against the head and block.

alloy head petrol then its about 80lbs .diesel around 90 to a 100 not sure their as i just pull any head bolt down till i feel the bolt stretch but i wouldnt advise anyone to do it my way unless its another mechanic ,you know the sort of thing with a few mechanics taking the rise out of one and other ,like what do you want the torque wrench for ,you a weekend mechanic or what .

22 - 24 ft. lbs. for the rod caps and....
Cylinder Head Tightening Torque and Sequence.

Tighten cylinder head bolts in order shown.
Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

Loosen bolts in reverse of order shown.

Retighten cylinder head bolts in order shown.
Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

Mark cylinder head bolts for rotational reference.
Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

CAUTION:

• Do not reuse the old cylinder head bolts.

hello where can I get some bolts for a 1996 kia sportage
2.0 dohc 1998cc fe 1995-02

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   
   Negative battery cable Intake manifold bracket upper bolts Clutch release cylinder and move it aside, if equipped Intake manifold bracket lower bolts and remove the bracket Starter from the clutch, manual transmissions only Starter from the torque converter, automatic transmissions only Starter electrical connectors Move the transmission wire harness aside Starter
   
   
   Fig. Exploded view of the starter
   

To install:

1. Install or connect the following:
   
   Starter to the engine well Starter electrical connectors Lower intake manifold bracket and install the upper bolts Starter into position. When aligned properly torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket bolts to 40 ft. lbs. (54 Nm). Properly position the clutch release cylinder, if equipped. Torque the bolts to 40 ft. lbs. (54 Nm). Torque the intake manifold bracket upper bolts to 40 ft. lbs. (54 Nm). Negative battery cable

Head bolts- 62 lb-ft cam pulley lock bolt- 42 lb-ft cam cap bolt- 16 lb-ft

hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .

1999 kia sportage 2.0 DOHC head torque

Thanks for using FIX YA !

J5