For most Ford vehicles you can self-program the remote for keyless entry. However there are some of the newer models that require professional equipment to program the keyless entry remote. You can check out what vehicles have self programming and which ones need professional programming here: https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm
In the meantime here are the most common Ford Keyless Entry Remote programming instructions:
*** THERE ARE 2 POSSIBLE PROGRAMMING PROCEDURES. ***Procedure #1Note: Obtain all remote transmitters for this vehicle.
Note: Do not depress the brake pedal during procedure.
Procedure #2Note: Obtain all remote transmitters for this vehicle.
SOURCE: 1997 Honda Civic EX Keyless entry programming
If you still have the factory radio, there is a way to split the power wire for the factory radio to the aftermarket radio. All you will need are the power and ground for your aftermarket radio, so the rest of the wires should be untouched on the plug for the factory radio. You can simply re-install the radio within the dash and retain the keyless entry as well as restoring your dome light function. Here's a PDF of some instructions. If you did not keep the radio, I would suggest looking online or ins ome junk yards, because it is needed. www.installdr.com/InstallDocs/Honda/PDF/466013.pdf
SOURCE: need keyless entry code for a 04 an 99 ford explorer
On your 99 model the module is located behind the left quarter trim panel,mid-way.You maybe able to see it by removing the speaker cover or the cupholder on top. The module will have a sticker with a 5 digit code.
On the 04 the model is behind the right quarter trim panel toward the front about even with the right rear door stricker.
SOURCE: how to reset factory code on keyless entry ford five hundred
if you do not already know the factory code, the only way it can be obtained is by your local ford dealer. the proprietary computer equiptment they have can access the code that is programed in vehicles security module. if you purchased it used..it is often that the keyless entry code id card is still withe the owners manual..it is a 5 digit code printed on an credit card sized card that is white in color..i hope this helps you...good luck
SOURCE: programming a keyless entry remote
Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.
Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming.
The vehicle must be OFF.
Place the replacement key fob in the console pocket with the buttons facing forward.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time.
When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes.
The DIC will display a message: OFF/ACC TO LEARN.
Press the OFF/ACC portion of the ignition button.
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode.
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation.
Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac.
SOURCE: I can't find the keyless entry code for my 2004 ford freestar
The code is on the fuse box under the dash near the hood release. On my van there are two bar codes on a sticker attached to the fuse box. Under the first bar code, on the right side is the 5 digit code (bring your glasses the numbers are really small). After you get this code, just search the internet and there are plenty of forums on programing the keyless remote and also adding your own unique number to the key pad entry.
Good Luck
652 views
Usually answered in minutes!
×