What are the toyota 3 y engine bolt torque specifications

Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 DegreesI would check in the service manual as well, just to be sure.

Question edited for clarity.
Question moved to model category.

All here for the three engine types

https://www.autozone.com/diy/repair-guides/nissan-frontier-xterra-1998-05-torque-specifications-repair-guide-p-0996b43f8037fa5c

https://www.google.com/search?q=2004+Nissan+Xterra.+cylinder+head+bolt+sequence+and+torque+specs

..

The main torque setting for the Toyota Corolla VVTi 1.3 engine will depend on the specific component or fastener being tightened. It is important to refer to the manufacturer's specifications or service manual for the correct torque values to use.
Here are some general torque values for common components on the Toyota Corolla VVTi 1.3 engine:

• Cylinder head bolts: 55 Nm (41 ft-lbs)
• Connecting rod nuts: 40 Nm (29 ft-lbs)
• Main bearing cap bolts: 65 Nm (48 ft-lbs)
• Oil pump bolts: 12 Nm (9 ft-lbs)
• Timing chain tensioner bolt: 25 Nm (18 ft-lbs)

It is important to note that these torque values are just estimates and may vary depending on the specific engine and component. Always refer to the manufacturer's specifications for the correct torque values to use.
In addition, it is important to use a torque wrench to accurately tighten fasteners to the specified torque. Using the wrong torque value or over-tightening fasteners can lead to problems such as stripped threads, damaged components, or engine failure.
I hope this helps!

Let me know if you have any questions.

20. INSTALL CYLINDER HEAD COVER SUB-ASSY
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:

Remove any oil from the contact surface.

Install the cylinder head cover within 3 minutes after
applying seal packing.

Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Install the engine wire harness with the 3 nuts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)
21. INSTALL CYLINDER HEAD COVER SUB-ASSY LH
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:

Remove any oil from the contact surface.

Install the cylinder head cover within 3 minutes after
applying seal packing.

Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Using an E6 torx) socket wrench, install the engine wire
harness protector with the 2 bolts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)

This is year/make/model specific to the 2nd Gen Sienna. Taken from the 05 Toyota Sienna repair manual. Hope this answers your torque specs for the valve covers which uses 10 mm bolts. If in doubt, as Scotty Kilmer asserts, do a "German tight".

go on line -typr in torque specifications for toyota 1jz engine and there will be a pdf spec sheet of all the vehicle torque settings.

Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

I AM LOOKING FOR CONROD BOLT TORQUE SETTING FOR A TOYOTA 2Z FORKLIFT

Hi. Thanks for your question. For Torque specification for engine of model 2KD-FTV Toyota you can visit https://www.reliable-store.com and download the entire workshop manual which includes all the information along with the diagrams for better understanding. Good day!

heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbs

Crank Main caps Tightening Torque

For the 12 Pointed Head Bearing Cap Sub-Assembly Bolts
Start from center bolts and tighten in a clockwise rotation working out
Step 1 all bolts 22 Nm or 16 ft lb
Step 2 all bolts 44 Nm or 32 ft lb
Step 3 all bolts 45 degrees additional clockwise rotation using an angle indicator.
Step 4 all bolts 45 degrees additional clockwise rotation using an angle indicator.

Hexagon Head Bearing Cap Sub-Assembly Bolts
1ZZ-FE Engine 18.5 Nm (14 ft.lb)
2ZZ-GE Engine 18 Nm (13 ft.lb)

Connecting rod:
1. Apply a light coat of engine oil on the threads and under the heads of the connecting rod cap bolts.
2. Install and alternately tighten the 2 connecting rod cap bolts in several passes. Torque: 1ZZ-FE: 20 Nm (204 kgf-cm, 15 ft. lbs.) 2ZZ-GE: 30 Nm (306 kgf-cm, 22 ft. lbs.) If any of the connecting rod cap bolts does not meet the torque specification, replace the connecting rod cap bolts.
3. Retighten the cap bolts by 90° more
4. Check that the crankshaft turns smoothly.