Question about Chrysler Cars & Trucks

Open Question

Where is the location of the transmission control solenoid on a 96 Chrysler Town and Country

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
garyq1970

Gary Queen

  • 85 Answers

SOURCE: changing fuel filter on 2004 chrysler town and country

  1. Remove or disconnect the following:
    • Negative battery cable
  2. Raise the vehicle and support the fuel tank with a transmission jack.
    • Fuel line from the front of the tank
    • Ground strap
    • Inboard side of the fuel tank straps and front T strap fastener and lower the tank about 6 inches
    • Fuel lines from the fuel pump module
    • Fuel filter
  3. Installation is the reverse of removal. Tighten the fuel filter bolts to 40 inch lbs. (4.5 Nm), the main tank straps to 40 ft. lbs. (54 Nm) and the T strap to 250 inch lbs. (28 Nm).
  4. Start the engine and check for leaks.

Posted on Aug 24, 2008

Ad

Anonymous

  • 152 Answers

SOURCE: Where is the Body Control Module located?

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the bcm.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the bcm to the jb. Slide the bcm downward to disengage guide studs on jb from channels on bcm mounting bracket
Remove bcm from jb.

Posted on Jan 02, 2009

Anonymous

  • 362 Answers

SOURCE: chrysler 2000 town and country says it's the tcm

Here's the location of the transmission control module.
4a2cf9b.png

Posted on Jan 31, 2009

emissionwiz

Marvin

  • 85206 Answers

SOURCE: where is the body control module located on a 1997 town & country

It is located on the back side of the underdash fuse box (junction block). You remove the lower steering column cover and knee blocker reinforcement. Then remove two plugs from the bottom of the BCM.
Remove the bolts holding the junction block to dash panel mounting bracket. Remove the junction block from the bracket. Remove screws holding the BCM to the junction block. Slide the BCM downward to disengage guide studs on jb from channels on BCM mounting bracket

Posted on Mar 23, 2009

chryslerguy

  • 323 Answers

SOURCE: locassion of output speed sensor on 2003 Town and Country

The input and output speed sensors look identical on the connector side. The one over the solenoid pack is the input, the one closer to the left frame rail or left front wheel is the output sensor. I hope this helps.

Posted on Apr 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 chrysler town and country limited 3.8litre where is the transmis 2003 Chrysler Town and Country limited recalls 2003 Chrysler Town and Country limited 3.8litre code p1776 how can I fix


It is not a do it yourself fix.

This is an automatic transmission issue which may involve replacing the valve body and solenoid pack and affects transmissions fitted to various Chrylser models. It could also be a symptom of more serious transmission problems and requires proper investigation and diagnosis.

On some models there was a Technical Service Bulletin issued to dealers on this problem .

Dec 15, 2015 | Chrysler Cars & Trucks

1 Answer

Where is the TCC solenoid pack located on a 1999 Chrysler Town and Country?


Find the transmission dipstick tube. Follow it down to the transmission. Just to the right you will see a large connector. Under that connector is the transmission control solenoid.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Apr 04, 2013 | Cars & Trucks

1 Answer

Lockup solenoid on 2000 town and country where is located


Inside the transmission attached to the valve body.

May 24, 2012 | 2000 Chrysler Town & Country

1 Answer

Where is transmission pump on 96 town and country inside or under


The transmission pump is located behind the converter, the transmission has to be removed to get to it

Oct 22, 2010 | 1997 Chrysler Town & Country

1 Answer

Where is shift solenoid for 2002 town & country?


It is located inside your transmission, you will have to take off the transmission oil pan to access it.

Jun 05, 2010 | 2002 Chrysler Town & Country

1 Answer

Looking for a diagram on removing and replacing the neutral safety switch on a 96 chrysler town and country



The Neutral Safety Switch function is controlled by the Transaxle Range Sensor (TRS). This Switch is Located ON the Transmission with Plug Facing UP and it is on the Bumper / Driver Side of the Transmission You Simply UNPLUG Electrical Connecter, And then the Unit Screws Out of Transmission Counterclock Wise, Install REVERSE Procedure.
NOTE: Be sure to have a DRAIN PAN Under your Work Area as there May be SOME Fluid Drainage When Switch is Removed, Swap them Fast if Fluid Comes out Fast so as NOT to have to Replace A Bunch of Trans. Fluid.

Oct 03, 2009 | 1996 Chrysler Town & Country

1 Answer

Trouble codes on a 2000 Chrysler town and country


0775 is Presure Control Solenoid "B", 0784 is 4-5 Shift these are trans codes from the transmission Solenoid. This is a changable part for any mech. Part is around $200 & includes the gasket.

Jun 26, 2009 | 2000 Chrysler Town & Country

1 Answer

Chrysler 2000 town and country says it's the tcm


Here's the location of the transmission control module.
4a2cf9b.png

Jan 29, 2009 | 2000 Chrysler Town & Country

3 Answers

Code0755 shift solenoid b after about ten miles next day whilst driving in fourth transmission goes into second


If you were to take the solenoid pack apart you would find a bad connection on that solenoid. You sill need a new pack installed.

Aug 11, 2008 | 1993 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...