2005 Chevrolet Impala Logo

Related Topics:

Chris Posted on Jun 16, 2018
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

My 2005 Chevy Impala driver seat is slitly twisted and won't go back all the way or forward any easy way to fix it and can't get back bolts out to remove and adjust???

1 Answer

Lonte J

Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

  • Expert 165 Answers
  • Posted on Jun 17, 2018
Lonte J
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

Sergeant:

An expert that has over 500 points.

Joined: May 18, 2018
Answers
165
Questions
2
Helped
41590
Points
511

Sounds like either something is jammed in the seat track and/or the track has to be replaced and that is a complicated operation there as I have replaced a number those. everything has to go back exactly as it came out or you have to take it out again and correct it and that in itself is no fun. Like I said, it may just be something jammed in the track but also, it could be a broken seat motor drive shaft and in which, the seat track or more commonly referred to and "seat module". That should be left to someone who has ahd experience in replacing them because they can be very tricky. I hope this helps you, Jesus loves you, John 3:16-17 (KJV)

5 Related Answers

Anonymous

  • 15 Answers
  • Posted on Aug 11, 2008

SOURCE: Power driver seat will not adjust forward or back.

My intuition tells me that the 6 way power seat track forward / reverse motor is bad. Sometimes you can replace just the one motor but most often a whole new power seat track is the only way to repair. It is not too bad to replace but the seat will have to be removed from the car and placed upside down to access the track assy. There are 2 bolts in the front of the seat and 2 bolts in the back of the seat that hold it down to the floorboard. Once it is loose you can rock the seat backwards to access and unplug the electrical connectors.

Ad

ITGuy181

  • 1 Answer
  • Posted on Dec 02, 2008

SOURCE: Engine Bolt Torques- 2005 Chevy Impala/3400 Engine

Head Bolts
Step one 37 ft lbs then tignten 120 degrees more

Rocker arms
Step one 11 ft lbs then tighten 90 degresss more

Upper intake
89 inch lbs
Lower intake
132 inch lbs

emissionwiz

Marvin

  • 85242 Answers
  • Posted on Feb 19, 2009

SOURCE: 2005 trailblazer driver seat will not move forward or back.

This kind of issus is almost always the power seat switch is defective.

Anonymous

  • 389 Answers
  • Posted on Jan 22, 2010

SOURCE: 2001 VW Beetle. The driver's front seat adjuster

I'm assuming you have manual adjustment seats. There is a spring underneath the seat that locks the end of the lever into corresponding notches in the seat frame rail. That spring has either fallen off or broken.

Anonymous

  • 1 Answer
  • Posted on Aug 07, 2011

SOURCE: 2003 Toyota Camry drivers side power seat stuck

This is not necessary...as many have stated...use a hammer with switch in reverse position. Hammer the seat back...it will catch...

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How to guide to electric seat removal on a 2005 chevy malibu

I'm assuming it is the front seats you are removing. There is two systems used to mount front seats, 4 bolt and 2 bolt. Both are easy to deal with. I think the Malibu uses the 2 bolt setup.
Slide the seat all the way forward and look at the rear end of the two runner grooves. There will be a bolt in each runner going down into the floor. It has a star shaped hole in the head. This is a 'Torx' head bolt, either a T40 or T45 size. Remove these bolts. You will probably need to unbolt the seatbelt mount on the floor as well. Tilt the entire seat forward and carefully unclip the electrical wire that is underneath the seat. While it is tilted forward pull the entire seat backwards. It should unhook at the front and lift out.
These seats are very heavy so be careful when lifting them out. Fitting is the opposite to this. Tilt the seat forward and hook in the front ends, connect the wire underneath, lower the rear end and bolt it down.
The four bolt system has two bolts at the front end of the rails instead of the two hooks.
0helpful
1answer

2005 impala power seat will not move.... Have been advised that worm gear is shot. How do Ie seat forward to remove?

If the gear is shot then the seat is not going to move you will have to hand wrench it loose. To ensure this is your problem un plug the motor and test the connection with a test light to ensure there is power. If there is you may be able to engage the motor and push the seat forward and back. Good luck this is a pain when the gear is shot or broken, there is no easy fix.
0helpful
1answer

How do i remove a fiat punto drivers seat

Theres only 4 bolts that hold the seat down 5 or 6 mm allen key bolts Dont forget the wire under the seat for the air bag. Move the seat fully forward take out the rear bolts, move fully back and do the front. Refitting is as easy
.
2helpful
1answer

2009 impala driver side power seat won't move up/down, makes whirring sound when attempted. Moves forward backward. Passenger seat works properly.

Before you do any of the expensive things disconnect and reconnect the wiring to the seat I had the same exact problem with my 2009 Chevy Impala and was ready to take it to the dealer when I disconnected the power cables to it and reconnected them I found that one of the Harnesses was loose and the problem was solved
0helpful
1answer

How fold down rear seats of a 2005 chevy impala

To fold down, follow these steps:
1. There is a loop located in the middle of the back seat - pull it forward and the bottom part of the rear seat will fold down
2. Wedge the the back seat, and it should not give you any trouble in folding down
3. To ensure that the seat goes all the way down- remove the headrest.
If your seat can not be folded-down, follow these steps to remove it:
1. Put some pressure on the bottom cushion of the back seat.
2. To release the bottom seat, pull the T handles, and then remove the cushion
3. There will be some bolts and screws on the bottom of the seat - remove them, and then you can pull out the seat.
1helpful
2answers

Automatic driver seat broken, how to fix/cost

The back and foward movement uses the same motor. So if it moves one way but not the other it's most likely the switch. Try to blow it out or clean it out. If pop or somthing spilled on it you will prob. need to pull switch out and take it apart to clean contacks inside.
0helpful
1answer

My daughter's 2005 grand prix will not start. How can she get in the trunk to get to her jumper cables because the key fob won't work to open the trunk and the inside trunk release won't work...

In your situation I think your best bet is going to be taking out the back seat. Luckily this is very easy and will allow you easy access to your truck and jumper cables. Okay in order to remove the back seat you will have to have a socket set. There should be 2 bolts holding the bottom of the seat down and you can find them on the floor on the front part of the rear seat. One bolt on the driver side and one bolt on the passenger side. After you get those bolts out you should be able to remove the bottom section of the seat. If you can not look for two more bolts on the back part of the seat. You will have to look between the back of the seat and the bottom part. After you take those two bolts out both parts of the seat should be free and you can remove them. I hope this helps.
0helpful
1answer

How do you take out a 06 chevy impala seat.-diver side-

Slide it all the way back. Remove the 2 bolts on the rails, then slide all the way forward and remove the 2 bolts holding the back part of the rails. Make sure seat heater is disconnected. Then remove the seat.
0helpful
1answer
Not finding what you are looking for?

817 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29490 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...