Question about Chevrolet Spark

1 Answer

Starting from no1 Cylinder What is the procedure to follow when setting the valves of a Chevy spark 800cc 3cylinder engine ? it has a coil PACk and not a distributor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 15,575 Answers

We know it doesn't have a dist. You really should buy a repair manual .

Posted on Jan 27, 2017

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How are the spark plugs wired from the coil pack?


You didn't mention whether this was a 4 cylinder or 6 cylinder. Below is a link to the procedure for swapping them out, and down around step 7 is a diagram that shows where each cylinder connects to the coil pack. Cavalier is the Chevy equivalent of the Grand Am. Same parts and procedures usually work for both.

V6Z24 How To Plug Wire Replacement

Jul 19, 2014 | 1993 Pontiac Grand Am

1 Answer

Toyota runx 140rt 2003. there is no firing activity in cylinder no1 but there is power supply to coil pack, coilpack works fine and there is also fuel delivery to the cylinder. all other three cylinder air...


Remove the No1 HT lead, stick in a screw-driver and hold near a metal body part while the motor is running. If you see spark, then the spark plug is faulty. If there is no spark, then the HT lead may be faulty.

Sep 03, 2013 | Cars & Trucks

1 Answer

Chevrolet spark 800cc tappet settings


can someone help i have a chevy spark 2003 800cc. we redone the whole engine it has drive for 276km and it just cut out and since we can't get it to start and the diagnostiucs don't pic up anything

Mar 31, 2013 | Cars & Trucks

3 Answers

NEED HELP WITH THE FIRING ORDER ON A 1997 JEEP WRANGLER 2.5L ENGINE. I BELIEVE THE ORDER IS 1-3-4-2 BUT WHICH CYLINDER IS 1,2,3,4 AND HOW IS THE DISTRIBUTOR CAP ORIENTED IN RELATION TO SAME? THANKS, BRIAN.


on the intake manifold it has the cylinders numbered 1432 and on the distributor it has the #1 pulg marked and will go in reverse directions so remove the cap if it has one and put the plugs on in order of the postion#1 on the distributroter then go 1342 if it has coils the coils pack will have numbers on the pack 12 34 so put the pulg wire on the way the coil is marked and the wat the intake is marked, there is only two ways it can be wired it's 1423 or 1234 so go for it. hope this helps.

Aug 17, 2010 | 1997 Jeep Wrangler

1 Answer

Got a 99 chevy s10 with a po 303 code any help would help


Your P0303 means: "Cylinder #3 Misfire Detected." This could involve a simple matter of a bad spark plug, plug wire or something a bit more serious. If you have separate coils for each cylinder or groups of cylinders, then you need to check the coil pack to the coil over #3 Cylinder. Sometimes it could also mean a vacuum leak ANYWHERE on the Engine and lastly a Valve problem in that the intake or exhaust valve on Cylinder #3 is carboned up. I would recommend getting a Haynes Manual, available at most part stores to go through their diagnostic as to your misfire. Remember, in obtaining a Code, it has a lot more to do with a simple 'misfire detected', it's a starting point to where to look. A vacuum gauge and a compression gauge would help should it not be something so simple as a spark plug, plug wire, coil or a distributor cap & rotor button that has too much corrosion on it.

I hope this helps you a little,

As Always,

"00 Buck"

Jul 08, 2010 | Cars & Trucks

4 Answers

I have a ford explorer 99 but it's giving a error code PO306 what do u think it is


It sounds like a misfire. Check spark plugs 5 and 6. It could be bad fuel, bad plug wire, or weak coil. Check the fuel injectors as well. Other possible causes could be an egr valve stuck open, vacuum leaks, low fuel pressure.

Feb 17, 2010 | 1999 Ford Explorer

1 Answer

Dont know how to take master cylinder off to replace coil pack


You shouldn't have to remove it....here are the steps from the tech manual:

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Label and disconnect the spark plug wires from each of the coil pack towers.
3db79bc.gif
Ignition coil removal—2.4L engine

2f61688.gif
Ignition coil removal—3.3L and 3.8L engines


  1. Disengage the electrical connector from the ignition coil pack.
  2. Remove the coil pack mounting fasteners.
  3. Remove the coil pack from the vehicle. If equipped, remove the coil pack from the mounting bracket.
To install:
  1. Place the coil pack into position on top of the engine valve cover, or mounting bracket, if equipped.
  2. Install and tighten the coil pack mounting fasteners to 9 ft. lbs. (12 Nm).
  3. Plug in the electrical connector to the ignition coil pack.
  4. Connect each spark plug wire to each corresponding coil pack tower. The coil pack towers are numbered with the correct cylinder identification. Be sure that the spark plug wires snap firmly onto each coil tower.
  5. Connect the negative battery cable.

Jan 18, 2010 | 2001 Chrysler Voyager

1 Answer

Coil pack


On all four cylinder sit on top of engine toward back, follow spark plug wire from top of valve cove to coil pack. On six cylinder engine the ignition coil sit inside the distributor under the cap where the spark plug wires go.

Jan 06, 2010 | 1998 Chrysler Sebring

4 Answers

Distributor cap and rotor location on chevy silverado


Most chevy 5.3 do not use a cap and rotor. Most have single coil per spark plug and wire. Trace spark plug wires to coil usually above the valve cover.

Dec 28, 2008 | Chevrolet Silverado 1500 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

202 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...