Ck engine light on code po335 p1336 also location of sensor?

Here's a couple of sites that will help you.

https://www.google.com/search?q=cam+position+sensor+located+on+a+1998+mercury+villager+van&newwindow=1&sxsrf=APwXEdcUmtJI87544mVJuuVLmrnUEaAS9w%3A1686089590328&source=hp&ei=dq9_ZI23EdKpqtsPutWL8A8&iflsig=AOEireoAAAAAZH-9hulTEtbyFeAiAZcw2CiwGgT8DLzp&oq=cam+position+sensor+located+on+a+1998+mercury+villager+van&gs_lcp=Cgdnd3Mtd2l6EAEYADIFCCEQqwJQAFgAYPUkaABwAHgAgAHSBogB0gaSAQM2LTGYAQCgAQKgAQE&sclient=gws-wiz

Best to you.

How to Fix error code P0300 for random misfires on your car ...

diy-auto-repair.wonderhowto.com/.../fix-error-code-p0300-for-random-...

Oct 15, 2010 - How to Fix error code P0300 for random misfires on your car ... amisfire (code P0304) on a 1999 Mercury Villager 3.3L · How to Fix error code P0500 ... I reset my codes and it ran fine for a couple of days, then I started getting ...

(code P0305) on a 1999 Mercury Villager 3.3L - auto repair

diy-auto-repair.wonderhowto.com/.../troubleshoot-misfire-code-p0305-1...

Sep 7, 2010 - The vehicle is a '99 Mercury Village, 3.3L, with 150000 miles on it. The chief ... How to Fix error code P0300 for random misfires on your car ...

2000 Villager Misfire - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Mercury > Villager

May 24, 2010 - 2000 Villager Misfire Villager Car Forums. ... i was told that the 3.3L engines of 1999-2002 nissan quests/ mercury villagers are INTERFERENCE engines! ... Hope the following may help, and I will post if my last fix works. ... I have a 1999mercury villager that is showing a random multiple cylinder misfire ...

Rough Idle - 2000 Mercury Villager - RepairPal

repairpal.com > Questions > Mercury > Villager > 2000 Mercury Villager

Repair the code issue, because your Villager has OBD-II which is a very helpful Diagnostic system. Upvote (4) ... My 1999 Villager was running poorly; rough idle, lack of power at highway speeds and the engine problem light indicated random miss-fire, etc. I had new spark ... Have code po306 cylinder 6 misfire detected.

P0301 - OBD-II Trouble Code - RepairPal

do not ever change the knock sensor unless you have $600 to throw away for nothing. You need a new distributor. teh cam sensor is going. it's in the dist. & not serviceable.
Buy a Rich Porter reman on ebay for $200. They will run cold whent hey start to fail, tehn totally fail.

go here & join the group for free tech help

http://groups.yahoo.com/group/villagerquest/

it could be faulty fuel pump or coil pack transistor.

I have a 1997 Mercury Villager with many miles. We get poor gas mileage. The check engine light is on. I want to replace the 02 sensor but cannot locate it on the engine. Is there a link with photo of physical location of the sensor and what are the steps to replace it?

it's in the valley of the engine. Do not ever replace it even if you get a code. A knock sensor will NEVER casue a driveabiity problem. It only retards timing 6 degrees if it senses spark knock. It also sets a code if an engine mount is broken and the engine rocks up and down on acceleration.

go here for help

http://groups.yahoo.com/group/villagerquest/

According to the Haynes manual it is under the intake manifold, Upper and lower intake manifolds must be removed for access. If you go to Auto Zone, they have the sensor and can give you the step by step instructions to replacing the knock sensor with common tools. Good luck and hope this help.

CODE PO325 - KNOCK SENSOR. CODE PO335 -CRANK SHAFT POSITION SENSOR. CODE PO336 - I DID NOT SEE CODE PO336.

Here is a image of it's location, I hope it helps.

go to this website where there are files that will help you diagnose your issue.

http://autos.groups.yahoo.com/group/villagerquest/

P0135 is for heater circuit portion of the oxygen sensor circuit, not the sensor itself. It would just mean it's not heating the sensor so it will just delay the sensor controlling fuel trim until a few minutes later.