SOURCE: I have an 2006 Pontiac
hi, this is due to oil pressure send to the exhaust camshaft position sensor,, before u change this sensor or checking engine timing,, change the positon of sensor a to sensor b and check the dtc if it is still p0014, if other dtc will send to ecmit means that the sensor is the problem, if P0014 still the code, you may now check bank 1 timing
SOURCE: where is the intake camshaft position actuator
if it is a V-6 engine look on the belt side of the motor. You will see a black cover with a connector right behind the serpentine belt about in the middle of the engine.
if its a 4 cylinder there will be two of them located under the engine cover and mounted on top of the valve cover towards the front of the engine.
I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa
SOURCE: I HAVE p0010 code Problem.CAMSHAFT
P0010 - "A" Camshaft Position Actuator Circuit (Bank 1)
A P0010 code refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car's PCM (powertrain control module). That consists of an oil control valve (OCV), also called a solenoid valve and other components. Basically the check engine light and associated P0010 trouble code means that the voltage in the circuit has fallen below a set limit for a specific amount of time (varies by make/model/engine).
Symptoms may include:
* Check Engine Light illuminated (Malfunction Indicator Lamp)
* Rough running
* other symptoms may also be present
Causes: A code P0010 may mean that one or more of the following has happened:
* Faulty oil control valve (OCV)
* Open or short in the VVT/VCT circuit
* Open or short in the OCV / solenoid valve
* Damaged computer (PCM)
Possible Solutions: Some recommended troubleshooting and repair steps are:
* Carefully inspect the Bank 1 VVT/VCT system circuit wiring and connectors, repair as required
* With a warm engine, test the operation of the OCV, replace/repair as needed
Hope this helps to solve it (remember to rate this answer).
SOURCE: camshaft position sensor a circuit bank 1 or
for the code po340 go to this site it will help you out. obd-codes.com/po340
SOURCE: where are the camshaft and crankshaft position sensors on 2001 silverado 8.1 V8
Crank shaft sensor
Remove the driver side rear ignition coil bolts. Reposition the coil. Disconnect the crankshaft position (CKP) sensor electrical connector. # Use penetrating oil and allow the oil to soak around the CKP sensor prior to removing the sensor. You're looking at left, rear side of engine.
CAMSHAFT POS.
front side of engine on the drives side about half way up the timing cover, not hard to get to.
?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.
DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .
P0010....'A' Camshaft Position Actuator Circuit (Bank 1)
P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)
P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)
P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)
P0020....'A' Camshaft Position Actuator Circuit (Bank 2)
P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)
P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)
P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)
P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)
P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)
I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,
180 views
Usually answered in minutes!
×