Front Bumper I need a front bumper for my 95 Jaguar XJS......can you help me?

Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

Front bumper requires removal to gain acsess to the lower 10mm bolts. Bumper comes off by removing the 2 10mm bolts on the top of the bumper then unscrew the 2 T30 screws in the front wheel arch liner (bumper side) and then you will be able to see a 10mm bolt reversed into a bracket at the top of the bumper from a inside veiw, remove and repeat for the other side. Then its 3 10mm bolts that secure the front under tray (if yours has one). Then there will be another 10mm bolt to the wing side of the headlamp from a above veiw. Bumper should then just pull off and watch for the connector for the fog lamp harness.

Just the 2 lower headlamp bolts andit should pull from its housing

have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal

1. Raise and support the vehicle.
   

1. Remove the RH and LH front wheel (1007).
   

1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).
   
   
   
   
   

1. Remove the four front fender brace screws.
   
   
   
   
   

1. Remove the two front fender brace nuts.
   

1. Remove the two plastic screws.
   

1. Remove the seven clip buttons located under the front bumper cover (17D957).
   
   
   
   
   

1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
   

1. Remove the four front bumper cover brace bolts.
   
   
   
   
   

1. Remove the front bumper cover from the vehicle.
   
   
   
   
   

1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).
   
   
   
   
2. Remove the eight front bumper bolts.

1. Remove the front bumper from the vehicle.
   

hey go to this website they have all the stuff for jags, their in houston,texas and i have used them to order parts for my 85 and 79 jags :p

http://www.motorcarsltd.com/

if this helped, please rate me or what ever! :p

The strip is held on with really tacky glue. You will have to pry off one end and pull off the remainder of the strip.

how do you remove a front bumper off of an jaguar s type?

1/Remove bumper under tray.
2/ " the front of both inner wheel liners.
3/ " a 10mm bolt at top behind both marker lights.
4/Remove 2 10mm bolts above both headlight assemblies.
5/Cautiously withdraw bumper then disconnect bumper harness.

thier are companies that sell OEM parts cheaper and they arrive undamaged. I can get that bumper for 225.00 in threedays