20 Most Recent 2004 Chrysler PT Cruiser Questions & Answers

it is in limp mode to protect the engine and transmission run the fault codes and fix what is found

Question edited for clarity, add maker and fix typo. Question moved to model category. There are 4 screws underneath that fix top half to bottom half. https://f01.justanswer.com/dcraig1000/a95a6021-585a-41cf-9a2a-04e4fb48f2bc_eee1.pdf ..

Question edited for typo Question moved to model category. Thoroughly clean the Throttle Body and Idle Air Control. Classic causes of 'rough idle'. https://www.google.com/search?q=2004+chrysler+%22pt+cruiser%22+P0172

Idle Air Control Valve on 04 PT Cruiser??? Where is it??? ...

RepairPal.com https://repairpal.com > ... > PT Cruiser > 2004 Aug 23, 2010 - I want to clean my IAC, but can't figure out where it is exactly. On another website (PT Forum) there is a pic, ... 2004 Chrysler PT Cruiser. 1 answer · Top answer: Sorry, cannot insert photos here. The IAC is mounted on the throttle body ..

Take the braket out of the way or loosen and raise the engine to where there is room to remove and replace the pan

It is important to check teh oil. Low oil means low oil pressure and the car will not start. Try that good luck

Question edited to add maker. Question moved to sub category. Check out the videos. The large hose at the left rear is where the air enters the plenum, before entering the engine. It is rubber and stretchy, so you can make it meet. https://www.google.com/search?q=2004+Chrysler+PT+Cruiser+Turbo+replace+air+filter ..

you do not need to reprogram the ecu. has your mechanic checked for codes. has he checked the crank position sensor? and the cam position sensor?what the fuel pressur regulator.yiming belt and or the ignition coil

Or put key in on position for ten minutes......criminals cant wait for security to reset

https://answers.yahoo.com/question/index?qid=20160211114925AAUJges https://www.justanswer.com/chrysler/8wx4x-chrysler-pt-cruiser-location-2006-fuel-shut.html

Of course. You upset the anti-theft system. Number one tip. Find a way to keep power to the vehicle as you swap batteries over! I use a couple of lengths of wire or booster cables. https://www.fixya.com/cars/r26859529-resetting_vehicle_anti_theft_system ..

Does the engine crank, but not start or will it not crank? If not cranking, test battery, clean post and check wires for corrosion and good contact. Also check the ground wire between the engine block and the car body for good contact. If all good there, may be a problem in the ignition switch. If the engine cranks but will not start, check the pressure on the fuel rail. If good pressure, check the ignition module.

Hi there's this website something like reliable-store and it is very amazing for manual for repairing servicing anything someone on fixya recommended it to me and I thank him even today They have full manuals and it's verrrrry cheap and mine I got free in offers 3rd time I bought it, I also had an issue with the file so the girl replaced it in 30 mins there is one website more but i don't remember its name it was 2 years back bitman something link this Try these out brother

Clock Setting Procedure (digital clock page 242 of your owners manual) 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side Tune/Audio control. 5. To exit, press any button/knob or wait 5 seconds. SETTING THE ANALOG CLOCK (page 238 of your owners manual) To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct. The clock will adjust slowly at first and then quicker the longer the button is held.

Trouble Code: P0572

Brake Switch Signal No. 1 Circuit Low

Trouble Code Conditions:Ignition is on. When PCM recognizes that brake switch is mechanically stuck in the low/on position, a DTC will set. Three global good trips are necessary to turn off MIL.

Possible Causes:

* Brake switch signal circuit is shorted to ground
* BS No. 2 signal open
* Brake switch is damaged or has failed
* PCM has failed

i would check the brake switch first located under dash and when brake is pushed it hits switch turn ignition on and test the wires if all hot then switch is bad, other wise there is a short or bad pcm and these are not easy fixes requires knowledge of car wiring and diagnostic tools/computer

The relay box is under the hood on the drivers side of the vehicle. Should be a schematic inside the cover relating to which relay is which

My friend is a part time mechanic he gets his solutions from www.reliable-store.com he gets from their every single detailed info, instructions, diagrams, error codes, troubleshooting, transmission etc. everything on all vehicles, and factory manuals for service, repairs, parts, owner's, operations, maintenance etc. U can get help from there there is a girl at chat she can help you

My personal suggestion would be to go for these repair catalogs. I know this website www.reliable-store.com that i used to get manuals from, and they have all models online. I also brought for my 1989 BMW, such old model, they had it and it was very good manual. Go ahead, I bet.

Testing the starter electrical circuits is how to find the problem . Viewing wiring diagrams to see what all is involved in the starting of your vehicle ? Most vehicles have a starter relay that is energized by the PCM/ECM - engine computer . B+ voltage comes from the ignition switch going through the starter relay control side to the PCM - which will ground that circuit turning on the relay sending B+ voltage to the S terminal on the starter solenoid . Do you know what a automotive relay is an how to test ? How to test for B+ voltage at the starter ? How to use a DVOM - digital volt ohm meter ? Free wiring diagrams here http://www.bbbind.com/free-tsb Enter your vehicle info. year , make , model and engine size. Under system click on engine ,then under subsystem click on charging system . Click the search button then the third blue link , this is the starter electrical circuit . This diagram doesn't show the park neutral safety switch input to the PCM . Speaking of the park neutral switch , put transmission in neutral an see if it starts then , could be the switch is bad .

When you turn the key and it doesn't start, what happens? Do any of the dash warning lights come on? Does the engine turn over but not start? 1. If the dash lights DO come on every time, but the engine doesn't turn over every time, it's probably not a problem with the switch. Might be a bad starter relay. 2. If the dash lights DON'T come on every time, then it could be the switch (electrical contacts only working sometime). First, try spraying WD-40 or electrical contact cleaner into the lock area to see if that helps. If it doesn't, then you probably need a switch. Do a search for "ignition switch 2004 PT Cruiser" and you'll probably find what you need, including instructions. Be sure to disconnect battery before replacing the switch and follow precautions against activating airbag accidentally.