20 Most Recent 2000 Jeep Grand Cherokee - Page 3 Questions & Answers

it is as hard as it looks, the book says to take it to the dealer,

it could be a problem with the wiring with the sensor. You would need a multi-meter to check the wiring. Diagnostics cannot tell if the sensor is bad, only that the information sent does not agree with what should be reported.

when did it make the clicking. was it when turning sharp, if not it is another issue

back firing ( explosions in the exhaust) can be from fuel mixture too rich and unburnt fuel is getting to the hot exhaust possible causes for that are excessive fuel pressure , leaking injectors ,leaking injector seals backfiring through the inlet manifold can be calve timing, ---cam advance servo-- valve staying open ---valve clearance , problem hydraulic cam follower , incorrect firing order for the plug wires, crank/cam position sensors or wiring IN this country there is a joke about jeeps Santa was late with the presents because he bought a jeep ( jeep add about Santa buying a jeep released by jeep) Don't send it to a scrap yard as there are people who can fix jeeps

Stop leak can cause the radiator ports to get clogged. But if your car isn't getting heat, it's probably your heater core. The heater core is usually burried in the firewall between the engine and where you or your passenger put your feet

not sure what type vehicle we're talking about here, although you can lube up the rack and pinion or grease up your upper, if so equipped, and lower ball joints.

Didn't notice which Jeep model/year you have but if it didn't have those issues before, make sure you don't put the filter on backwards.

Hello Faye Sims, Whatever you are looking for... it is big & common to a lot of circuits... My best advise when starting to trouble-shoot MULTIPLE ISSUES is a start at the MAIN BATTERY & GROUND connections. (unless your CHEROKEE has recently been flooded). Start at your battery posts and move METHODICALLY through your main body (ground) & Starter cables (battery) and make sure the connections are clean and tight. Look for corrosion, breaks or discoloration of insulation or any signs of heat... Unless you are in a terrible rush... Shop for best prices from reputable sources (Like: Rockauto, Napa, even eBay & AMAZON (etc.))... also such products as CONTACT CLEANER, NALOX/NoCo & battery washers (in my opinion... are a MUST on AUTO-BATTERY posts). See here: Amazon com Battery Anti Corrosion Washers 2 Red 2 Black Automotive Quality High IMPEDANCE (or No Contact) VOLTAGE TESTERS... will protect existing circuits while attempting to find faults... (without FEAR of triggering EXPLODING AIR BAGS (in my opinion))... Or destroying semiconductors w/ spark... Klein Tools NCVT 2 Dual Range Non Contact Voltage Tester Amazon com Amazon battery cable Amazon com Deka 00297 Positive Battery Cable Automotive Rockauto battery cable (less $, 3 years, 36000 miles) http://www.rockauto.com/en/catalog/jeep,2000,grand+cherokee,4.7l+v8,1381418,electrical,battery+cable,2500 Finally... Check out buying A FUSE at your local parts store (abusive & egregious $$$$ (know your FUSE TYPES)) Amazon com Bussmann NO 44 ATC Blade Fuse Tester Puller Kit Automotive Comment me back... Spent a lifetime doing this... (love it) Free Drawings at BBB Industries (registration is required... these are real drawings) Hope this helps

Cabin air filter maybe clogged , if your vehicle has one . google cabin air fliter for your vehicle.

How about plugs wires.

I would take it to the shop that did the repairs and take them for a ride and let them know it started after the repaired the brakes.

what did the shaft look like, and did you notice a burnt smell when you took the shaft out?

Have You Tried Changing The Dimmer Switch!!! More Info If Not Good Luck !! We Are Here To Help !! Donald Deane MCSE,ASE,CPO