1998 Chevrolet Lumina - Answered Questions & Fixed issues

Where is cylinder 5 on a 2011 Chrysler 300

Check with your local wrecking yard. They have the interchange manuals.

replace the headlight switch is a good start to your problem, and check the brake light switch for being out of adjustment or no voltage or both.check all the light bulbs to see if they are all working and reinstall them

sounds like you may have a electrical connector that is not making a good connection, possible causes are loose connector-wiring is broken-wiring is over heating and the plastic is burned and /or the wiring pins are oxidized and dirty from heat .

Hi. I read your inquiry but I'm unsure of what your asking. The brake lines don't go straight to the brakes. What are you asking about "two upper and two lower"? These lines can not be confused. From the master, the two supply lines run to the ABS module. From the ABS module four different lines run out to each wheel. If your interested. eBay sells a complete pre-bent brake line kit. eBay Product Number: 3015274614 You could also call your local part store for availability or if you have the tools. You can save the money and bend them. I hope this helps. Please write back if you have any other information. Good Luck.

Usually it is a fuel pump relay that does not supply a "prime cycle" when the key is first turned on.The fuel pump will get power when oil pressure is present,but you have to crank it a bit before oil pressure builds sending power to the pump only then and while it;s running. A bad temp sensor can cause slow starting also.

Visit the on-line store, known as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem. Best Manuals

in diagnostics, your problem is called a "window". this kind of failures are annoying, both for the owner and the mechanic. the window will open and close randomly, and you need to be ready to see the fail and with all the tests you will do to find the cause, before the "window" closes. I suggest you identify what happened when your car stopped, in order to replicate as necessary to look for the culprit.

Rough idle could be the throttle position sensor, or the idle air control valve.abs could be you need brakes or just the abs sensor is bad

Change the fan relay in the fuse box under the hood. There are 2 one for air condioner on and one for temp sensor.

When I look up something in PARTS... and find them in bunches... Lots... New and IMPROVED... I know (in my heart)... the OEM (original equipment was pure trash... (garbage))... In my opinion you are lucky to be alive. I would simply advise you try another dealer... and then start ESCALATING... Let your fingers do the walking... START PHONING AROUND... Take good notes... These junior executives have to feel important too... and they cannot FIX what they do not know about. If you are up to a genuine CRUSADE ... Then try using the CUSTOMER ADVOCATE services of your local broadcast NEWS STATIONS... I think they like to tally community service points (I'm sure there even a GREAT story behind all that)... ELSE... BUREAU of Auto Repairs, small claims... (heck... the Supreme Court (if you have the time & $$$)). More Information for DORMAN 576358 More Information for PLATINUM PRO FTK010006 As for me... What did you hit...?? Carnac the Magnificent

Connect a scan tool to the car and check for DTC codes. If the car stalls likely a check engine code is set. Your friendly auto parts stores will provide this as a complementary service.

Do It Yourself and DIY Auto Repair by ChiltonDIY Haynes Manuals Car Repair Manuals Chilton Haynes Bentley

Sounds you have burned up the engine bearings. In other words you will need a new engine.

Top right between speedometer and temp gauge around the 80 mph mark

Mass airflow meter needs to be cleaned. There is a special spray cleaner for that purpose. Don't try any other kind of cleaner or you will destroy the sensor wires.

Open the hood and you will see an item that looks like a small bubble level. Have the car as level as you can, and there are adjustment screws near the levelers that will adjust the headlights. I would recommend having the vehicle pointing in a direction that will help you determine where to adjust them too

It if just goes click your engine may be seized up, try turning it by hand to see if that is the case.

I found this picture, you get at from inside the trunk, correct. My info says to use bezel socket tool, the bezel is number one in the picture. I don't know about that tool? If you can remove bezel w/o?