20 Most Recent 1997 Chevrolet Lumina Questions & Answers

Question edited for a lot more clarity. Question moved to model category. It might be the flasher relay and it might be the horn relay although horns tend to seize up through lack of use. the flasher relay is is separate to the Hazards relay which is often part of the switch. https://www.google.com/search?q=1997+chevy+lumina+flasher+relay+location

Chevrolet Lumina (1997) - fuse box diagram - Auto Genius

https://www.autogenius.info > chevrolet-lumina-1997-f... Jan 1, 2018 - Fuse, Description. 1, CIGAR LIGHTER - Instrument Panel and Console Cigar Lighter. 4, WAC- WAC Control Assembly Solenoid Box, Mix Motor, ...

Chevrolet Lumina (1995-2001) fuses and relays

https://fuse-box.info > chevrolet > chevrolet-lumina-19... Here you will find fuse box diagrams of Chevrolet Lumina 1995, 1996, 1997, 1998, 1999, 2000 and 2001, get information about the location of the fuse panels ... Easiest way though https://www.google.com/search?q=auto+electrician+near+me ..

Irrevocable damage on a vehicle that age. Cracked piston, broken or seized rings, stuck valves, cracked head. damaged bearings. The list is long. The first thing to do is use a stethoscope and trace exactly where the tapping is coming from?

The other wires should go with the battery wire on the big post on the starter.

Check fuses I found fuse box diagram which one of the fuses is for Theft-Deterrent Module, Radio. I would go through and check fuses Chevrolet Lumina (1997) - fuse box diagram - Auto Genius Some info no theft-deterrent below 1997 Chevy Lumina Car Will Not Start. "security" (2carpros.com) Security System Preventing Car From Running: Car Will Not Start, ... (2carpros.com)

It is under the car in the rear near the gas tank on a tray along with the carbon vapor storage canister.

The dealer recommend GM Dex Cool Antifreeze.
But there are complaint against this type of coolant.
http://www.stevesnovasite.com/forums/archive/index.php/t-128547.html
In GM cars we replace Dex Cool with Prestone green coolant.
It's up to you. Ask before but if you decide to change the type of coolant then:
If your intention is to add coolant only, then you need:
Mix with
ANY COLOR ANTIFREEZE
ALL MAKES ALL MODELS
of cars and light trucks
add to ANY color antifreeze
PRESTONE
50/50
PREDILUTED ANTIFREEZE/COOLANT
EXTENDED LIFE up to 150000/mile 5 year protection.
DO NOT ADD WATER.

If your intention is to flush the RADIATOR (Cooling System), then you need:
Mix with
ANY COLOR ANTIFREEZE
ALL MAKES ALL MODELS
of cars and light trucks
add to ANY color antifrezze
PRESTONE
EXTENDED LIFE up to 150000/mile 5 year protection.
On the back you have to read directions:
Step 1 Drain. Step 2 Flush. Step 3 Fill.
Recommended to ad 30% to 50% volume, distilled water. If you flush the system and rinse with water you must add only 30% water to the antifreeze. There is more water trapped inside the engine compartment, because the thermostat is closed. Make sure to have a coolant density tester. When you finish one of 5 balls must sink, that indicates that you reached 50/50 strength. That means 50% Prestone and 50% Water, which will provide to your car a -34F degree FREEZE-UP Protection , and +265F degree BOILOVER protection.The next day,with a cooled engine open radiator cap, and test the strength of coolant. If not quite right, then siphon coolant from the radiator and add antifreeze, or distilled water as necessary.
Make sure to disposal the used coolant properly.

P1895 Engine control module (ECM), actual torque signal - circuit malfunctio Sell this motor quick ,these are nice cars but suffer for these problems because the computer is bolted to the inlet manifold and gets too hot then cooks ,all these petrol engines from around this time suffer from this fault

You've got a bad solenoid or a bad vacuum motor. You really need a shop manual with full vacuum and electrical diagrams. Call your local library and ask if they have free access to alldata or Prodemand or buy a subscription to alldatadiy.com or eautorepair.net. Print out the electical and vacuum diagrams and then conduct the tests shown in the shop manual. It's an easy fix but will take more effort to diagnose.

The window crank is held in place by a locking clip. Remove the clip and pull the crank off the shaft. If the crank is stripped, just replace it. If the shaft is stripped, you have to replace the entire window regulator. See this post on how to remove a window crank. http://ricksfreeautorepairadvice.com/remove-a-door-panel/

you need to read the manual for the machine you are hooking to the vehicle . These are errors not codes you need to understand how it works better.

Fuel pump is bad. At idle pressure should read 50 PSI. Replace with original manufacture fuel pump after market pumps will burn out fast and are unreliable from my experience. Also could have a bad fuel regulator but that only works while driving down the road full throttle. You can unhook the fuel rail pressure regulator and that will give it full fuel and the pressure reading should read 60 PSI while it is running. If you turn the engine off and turn the key to run position it should read 50 PSI and hold for 60 seconds, if it drops below 30 PSI after 30 seconds Pump is defective. Many pumps are going bad here of late as people have been running them less than ¼ tank and this kills the pump. The fuel cools and lubricates the pump so the lower the fuel level the worse it is on the pump below ¼ tank. Not to hard of a job to do if you want instructions let me know.

I had same problem . There is a vacuum resovoir tank located behind the left front splash shield . The vacuum line behind the battery goes to it . I removed two 5/32 screws just in front of the tire that hold the splash shield to the fender , carefully flex the shield away from the fender and take a look . I found the vacuum line had come loose , plugged it back on and everything works . Hope this helps

Get a wiring diagram and check for power on all the power wires at the ignition switch. This is a known problem

Found this info in your owners manual. If you don't have owners manual you can look at one for free. my.gm.com, type in year--make--model.

IF the harness doesn't match, you've got the wrong pump

it has command start ???? Is this some kind of aftermarket add on ? This shouldn't have anything to do with the running lamps . unless someone hooked something up in correctly . Does the car have DRL - day time running lamps ? The Daytime Running Lamps (DRL) control module is designed to automatically operate exterior lights depending on outside light conditions. The DRL control module operates in 2 modes: • The day mode In the day mode, the DRL control module turns ON the high beam headlamps at a reduced intensity when the DRL ambient light sensor detects daylight under the following conditions: - The ignition switch is in the RUN position. - The headlamps are OFF. - The park brake is OFF (released). • The low light mode In the low light mode, the DRL ambient light sensor detects darkness, turning OFF the high beam headlamps and turning ON the low beam headlamps through circuit 10. Additionally, the DRL ambient light sensor turns ON the following lamps through circuit 9: - The park lamps - The sidemarker lamps - The license lamps - The tail lamps

Which engine ? Antifreeze can cause the milky look if it got into the intake or exhaust and drawn into the EGR .

this happened to my car get new fuil pomp

sounds like the relay is hosed. Turn on right blinker and follow the blinker sound under the dash, usually. Usually the other relay will be right next to it. The relay turns the voltage on and off to make it blink