2012 Chevrolet Equinox LS 4dr SUV 2.4L 4-cyl. FFV 6-speed Automatic - Answered Questions & Fixed issues
2012 Equinox. Door locks operate intermittently (once every few days), so it isn't a wire or a fuse. My bet is that it is a relay or the body control module.
Did you hook up a professional grade scan tool an check BCM codes ,view live input data for power locks .
Door Lock System Components
The power door lock system consists of the following components:
• Driver door lock switch--Provides a switched voltage signal to the body control module (BCM) for both lock and unlock switch activations.
• Front passenger door lock switch--Provides a switched voltage signal to the BCM for both lock and unlock switch activations.
• Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of all doors and liftgate.
• Door unlock relay--Located in the I/P fuse block and controls the unlocking of the passenger doors and liftgate.
• Driver door unlock relay--Located in the I/P fuse block and controls the unlocking of the driver door.
• BCM--Class 2 module which requires programming when replaced
• Reversible door lock actuators in each of the doors
• LOCK/MIRROR 10 A fuse--Located in the I/P fuse block, supplies power for the door lock switches and relays.
• DR LCK 20 A fuse--Located in the I/P fuse block, supplies power to the relays.
DTC Descriptors
DTC B3125 00: Left Front/Driver Door Only Unlock Circuit
DTC B3130 00: All Door Unlock Circuit
DTC B3135 00: All Door Lock Circuit
DTC B3140 00: Driver Unlock Switch Circuit
DTC B3145 00: Passenger Unlock Switch Circuit
DTC B3150 00: Driver Lock Switch Circuit
DTC B3155 00: Right Front Lock Switch Circuit
The relays in the I/P fuse box are not listed because you can't change them so why show then . They are PCB - relays Printed circuit board relays , soldered directly to the circuit board inside the fuse box.
You best bet ,take it to a qualified repair shop. I would say the vehicle has a lose connection somewhere . Ground ,
My bet is that it is a relay or the body control module. ??? Then you would be wrong Take it to a professional before you start replacing parts it doesn't need .
2012 Chevy equinox smells like burning plastic
Burnt smell after starting 2013 Chevrolet Equinox. Turned key starter turned over slowly then started drove car however strong electrical burning smell after starting pulled over seen smoke coming from under vehicle. Car wouldn't start even with a jump starter just clicking sound then nothing while horrible smell of burnt electrical from under the hood. Towed it home it just clicked once. Lights, horn, flashers dash and power locks all working fine never had any problems. Thoughts starter or ??
Rear hatch keeps opens while driving...
Unless you have electrical diagnostic skills , I suggest you take this to the dealer ! The lift gate can be opened by operating the switch on the instrument panel. Battery voltage is supplied to the liftgate actuator through the body control module (BCM). The BCM will pulse the lift gate actuator when a release input is received through the key fob, or the instrument panel switch.
The body control module (BCM) receives an input from the liftgate ajar assembly. The ajar assembly is normally open when the liftgate is fully closed. When the liftgate is opened, the ajar assembly contacts close providing a path to ground. The driver information center (DIC) illuminates the rear access open message when the gate is open. The instrument panel cluster (IPC) receives a serial data message from the BCM indicating the liftgate ajar status. If this message is displayed and the vehicle speed is greater than 8 km/h (5 mph), a chime will sound.
It could be ajar switch is bad .
Trouble opening lift gate in 2012 Equinox computer saying rear door open
Hey Karen,
That lift gate has a control module that controls the operation.
It communicates with the latch and other body modules
If the info display is indicating it is open when you know it is indeed shut.....I would suspect the latch assembly. There is a micro switch in the latch that informs the module when the gate is closed.
A scanner is actually the best most efficient way to diagnose this issue. A good independent garage should be able to scan for you for a fee. It will be worth the fee. Also...the lift assist struts are problematic on this particular vehicle. They assist in opening and keeping the lift-gate open.
Where are the camshaft intake senor on a 2012 chevy equinox
1 - Q38 Throttle Body
2 - G18 High Pressure Fuel Pump
3 - B23F Camshaft Position Sensor - Intake
4 - B37 Engine Oil Pressure Switch
5 - B68 Knock Sensor
6 - B26 Crankshaft Position Sensor
7 - M64 Starter Motor
8 - Q2 A/C Compressor Clutch
9 - G13 Generator
Error code p062b 2012 equinox
Had the same problem on our 2012 Equinox today. Threw codes P026B and P062F. Appears to be a bad battery. Replaced battery and all seems ok now...keeping fingers crossed. My suspicion is that the faulty, dying battery caused a low voltage situation in the injector control module and thus those errors. Will see if the check engine light returns in the next 48 hours.
Transmission cutting out
She,s hooch, Take it to a GM Dealer, If it off the warrenty , Be prepared to get a nice hefty bill.
Not finding what you are looking for?