Certified STIHL 2 & 4 cycle Engine and Equipment Technician
Roland W VanLue posted an answer for this Husqvarna Garden:
"50:1 Husqvarna HP OIl"
Roland W VanLue posted an answer for this Husqvarna Garden:
"Your fuel octane is GREAT ! Good to hear you are using fresh fuel. Make sure to use..."
Roland W VanLue posted an answer for this Husqvarna Garden:
"50:1 Husqvarna Oil"
Roland W VanLue posted an answer for this Husqvarna Garden:
"Most 2 cycles have a pin in the piston groove that keeps the ring from traveling. The pin..."
Roland W VanLue posted an answer for this Husqvarna 155bt Gas Backpack Leaf Blower:
"Yes, the exhaust screen check is a must any time performance is low. Your problem sounds..."
Roland W VanLue posted an answer for this Toro Garden:
"1) has the mower been turned on its side recently? 2) Oil level? too full? gasoline..."
Roland W VanLue posted an answer for this Stihl Garden:
""
Roland W VanLue posted an answer for this Stihl Garden:
""
Roland W VanLue posted an answer for this Stihl Garden:
"11151201630, 11151201615 both are discontinued. Suggest you contact Ron's Saw Shop..."
Roland W VanLue posted an answer for this Stihl Garden:
"A hard pull on that unit would indicate a sheared flywheel key. The key is part of the..."
Roland W VanLue posted an answer for this Stihl Garden:
"If it has one, it will be directly in front of the spark plug. Most 026 saws did not have..."
Roland W VanLue posted an answer for this Husqvarna Garden:
".325" pitch, .050 gauge. The cutter tooth width is a little wider at the top front,..."
Roland W VanLue posted an answer for this Stihl Garden:
"WSR6F Bosch, BPMR7A NGK for both saws."
Roland W VanLue posted an answer for this Mtd Garden:
"Locate the two top auger housing fastening bolts and remove. The auger housing will tilt..."
Roland W VanLue posted an answer for this Stihl Garden:
"30' level, 5/32" fle"
Roland W VanLue posted an answer for this McCulloch 2815 2816 CHAIN SAW CARB THROTTLE CABLE:
""
Roland W VanLue posted an answer for this Toro Garden:
""
Roland W VanLue posted an answer for this Toro Garden:
""
Roland W VanLue posted an answer for this Ryobi Garden:
"Most common for a unit that has been setting with fuel in the carburetor to have varnish..."
Roland W VanLue posted an answer for this Ryobi Garden:
"Investigate the fuel line inside the fuel tank. Sounds like it may be split or cracked,..."
Roland W VanLue posted an answer for this Stihl Garden:
"There are several conditions and situations that this can occur, but let's try the most..."
Roland W VanLue posted an answer for this Stihl Garden:
".010" +/- .002""
Roland W VanLue posted an answer for this Stihl Garden:
"1) check valves inside the primer plate is sticking 2) fuel pump diaphragm is varnished..."
Roland W VanLue posted an answer for this Husqvarna Garden:
""
Roland W VanLue posted an answer for this Craftsman Garden:
"Yes, you will need to remove the starter for access. FYI, you have a Briggs..."
Roland W VanLue posted an answer for this Toro Garden:
"The shifting rods have slotted ends that match up to each other. Moving the slots will..."
Roland W VanLue posted an answer for this Toro Garden:
"Many times the rod is 2 pieces that join together with a slot made onto one end. Normally..."
Roland W VanLue posted an answer for this Craftsman Garden:
"Surging is more often caused by 'fuel starvation', and can best be check simply be..."