3Bernina Gal with a passion for saving vintage sewing machines
R.A. Ellis posted an answer for this Sewing Machines:
"Perhaps the feed dogs are worn down so they do not move the fabric properly. However, I..."
R.A. Ellis
R.A. Ellis posted an answer for this Husqvarna Viking Emerald 116 Sewing Machine:
"Use a zig-zag so the stitching will not pop when the fabric stretches."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Please explain your situation more fully. Is the fabric puckering where you stitch, or is..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"It is probably best to just purchase a brand new one. Trying to fix it may or may not be..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Set the stitch width to zero."
R.A. EllisR.A. Ellis posted an answer for this Janome Sewing Machines:
"Sounds like your machine needs service for an adjustment."
R.A. EllisR.A. Ellis posted an answer for this PfaFF Sewing Machines:
"Contact your dealer."
R.A. EllisR.A. Ellis posted an answer for this Bernina Sewing Machines:
"Page 5 of the manual. #32 ..."
R.A. EllisR.A. Ellis posted an answer for this Husqvarna Viking Emerald 116 Sewing Machine:
"If it's a mechanical machine, most likely the stitch width mechanism is frozen due to old..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"The factory default is the midway point between high & low numbers on each of the..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"If the needle is not centered over the hole when set on a straight stitch, your machine..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Try a brand new needle and verify it is threaded correctly. If that doesn't help, it..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"With the error message and needle problem, you should probably take it for service."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"If it is a mechnical machine (not computerized). Possibly the dial mechanism is stuck due..."
R.A. EllisR.A. Ellis posted an answer for this Husqvarna Sewing Machines:
"Sounds like the thread sensor is dirty or defective."
R.A. EllisR.A. Ellis posted an answer for this Brother Sewing Machines:
"You need to set the seam guide (or whatever you are using) to be 1/4" away from the..."
R.A. EllisR.A. Ellis posted an answer for this Brother Sewing Machines:
"Not sure what is your question, but this may help. Sewing Presser Feet"
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Try the correct category--not a sewing machine."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"If you are free motion quilting, you are manually moving the fabric while the machine..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"This will help you figure it out: Sewing Presser Feet"
R.A. EllisR.A. Ellis posted an answer for this Singer Sewing Machines:
"Loosen the top tension and lengthen the stitch length all the way Then sew two lines of..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"The top tension is intended to be adjusted for different uses and on different fabrics. ..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Sounds like the needle bar is slightly off center. Take it for service."
R.A. EllisR.A. Ellis posted an answer for this Husqvarna Sewing Machines:
"Increasing the top tension (and possibly decreasing the bottom tension) will cause the top..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Search for: Make Model accessories"
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Sounds like it may be the density or the material in the badges interfering with the..."
R.A. EllisR.A. Ellis posted an answer for this Bernina Sewing Machines:
"Perhaps the bobbin thread sensor is dirty."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Usually, you can find replacements at a dealer for your machine's make & model, or try..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Might try a different presser foot. Could be the machine is not reading the current..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Depends what E1 means for your machine model. On a lot of machines, it means it is..."
R.A. EllisR.A. Ellis posted an answer for this Sewing Machines:
"Probably no resolutions posted on the sewing machine query site."
R.A. Ellis
Sewing Machines 11670 answers
Computers & Internet 106 answers
Cars & Trucks 85 answers
Office Equipment &... 68 answers
Cell Phones 57 answers
Televison & Video 42 answers
Washing Machines 35 answers
Kitchen Appliances -... 33 answers
Crafts & Hobbies 30 answers
Tablets & eReaders 26 answers
2007 Saturn Sky Redline